User Guide M211095en-h


aD0! command and the number of parameters.aM!aSingle-digit WMT700 address that corresponds to the first character of the address



Download 8.38 Kb.
View original pdf
Page91/125
Date24.02.2019
Size8.38 Kb.
1   ...   87   88   89   90   91   92   93   94   ...   125
aD0! command and the number of parameters.
aM!
a
Single-digit WMT700 address that corresponds to the first character of the
address
value
M
Start measurement command
!
Terminates the command.
The response:
WMT700 User Guide
M211095EN-H
158

atttn
a
Single-digit WMT700 address that corresponds to the first character of the
address
value ttt
Period of time, in seconds, after which WMT700 has the measurement ready n
Number of measurement values WMT700 calculates and returns as a response to one or more subsequent
aD0! commands

Terminates the response.
Example
1M! 10025
Interpretation of the example message:
• Time after which the measurement is ready 2 seconds
• Number of returned measurement values To fetch the measurement results, use the
aD0! command aV! — Start Verification
This command starts verification. However, WMT700 does not return verification data directly after this command. It sends a response that specifies when the verification results can be retrieved using the
aD0! command and the number of parameters. The WMT700
verification data includes a watchdog count, sensor measurement unit settings, and the current SDI mode setting.
The command:
aV!
a
Single-digit WMT700 address that corresponds to the first character of the address value
V
Starts verification command
!
Terminates the command
The response:
atttn
Chapter 5 – Operation
159

a
Single-digit WMT700 address that corresponds to the first character of the address value ttt
Period of time, in seconds, after which WMT700 has the verification data ready n
Number of returned verification data fields

Terminates the response
Example
1V! 10014
Interpretation of the example message:
• Time when the measurement is ready 1 second
• Number of returned measurement values To fetch the measurement results, use the
aD0! command SDI Data Messages
When the SDI profile is selected, the data message sent by WMT700 depends on the command that you use before fetching the data with the
aD0! command WS425 AB SDI Message for C and M Command
When you give the commands


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   87   88   89   90   91   92   93   94   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Harley Davidson
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha