User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page9/125
Date24.02.2019
Size8.38 Kb.
1   ...   5   6   7   8   9   10   11   12   ...   125
Option
Unit Used
A
Meters per second
B
Knots
C
Miles per hour
D
Kilometers per hour Analog Output Signal for Wind Speed Channel
Ordering option 7 can be disabled or factory-configured for 8 different modes. WS425
options are usable and backwards compatible when replacing WS425 sensor with a
WMT700 unit.
Chapter 2 – Product Overview
21

Table 11 Output Configuration
Option
Output Configuration
0
Disabled
1
Voltage output 100 mV/m/s
0 mV = 0 ms mV = 40 ms (WMT701 maximum wind speed mV = 65 ms (WMT702 maximum wind speed mV = 75 ms (WMT703 maximum wind speed mV = 90 ms (WMT704 maximum wind speed)
3
Current output 4 … 20 mA, offset 4 mA
4 mA = 0 ms mA = 40 ms (WMT701, 0.4 mA/m/s)
20 mA = 65 ms (WMT702, 0.24615 mA/m/s)
20 mA = 75 ms (WMT703, 0.21333 mA/m/s)
20 mA = 90 ms (WMT704, 0.177778 mA/m/s)
Error indication sets output to 2 mA
4
Current output 0.2 mA/m/s
0 mA = 0 ms mA = 40 ms (WMT701 maximum wind speed mA = 65 ms (WMT702 maximum wind speed mA = 75 ms (WMT703 maximum wind speed mA = 90 ms (WMT704 maximum wind speed)
6
Frequency output 10 Hz/m/s
0 Hz = 0 ms Hz = 40 ms (WMT701 maximum wind speed Hz = 65 ms (WMT702 maximum wind speed Hz = 75 ms (WMT703 maximum wind speed Hz = 90 ms (WMT704 maximum wind speed)
7
WS425 voltage output 8 mV/mph
0 mV = 0 ms mV = 89.5 mph (WMT701 maximum wind speed mV = 145 mph (WMT702 maximum wind speed mV = 168 mph (WMT703 maximum wind speed mV = 201.3 mph (WMT704 maximum wind speed)
WMT700 User Guide
M211095EN-H
22




Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   5   6   7   8   9   10   11   12   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha