User Guide M211095en-h


Wx command with a character fixed-length data message.Character



Download 8.38 Kb.
View original pdf
Page83/125
Date24.02.2019
Size8.38 Kb.
1   ...   79   80   81   82   83   84   85   86   ...   125
Wx command with a character fixed-length data message.
Character
Description
1

02H (, start of transmission)
2
W
3
Averaging in seconds
4
Status: P = Pass F = Fail
5
Wind direction (most significant digit)
6
Wind direction (middle digit)
7
Wind direction (least significant digit)
8
Wind speed (most significant digit)
9
Wind speed (next digit)
10
Wind speed (next digit)
11
Wind speed (least significant digit. (dot character)
13
Wind speed (tenth digit)
14
Wind speed unit:
M = Miles per hour
K = Knots
L = Kilometers per hour
T = Meters per second
Chapter 5 – Operation
149


Character
Description
15
Checksum (most significant digit. For more information, seethe note below.
16
Checksum (least significant digit H (, end of transmission)
18
CR (carriage return)
19
LF (line feed)
The checksum is calculated from the characters from position 2 to 14. The accumulator initializes at 0 with the addition of the byte value. The checksum has a range of H … FFH.
Example
W5 W5P1200013.2TDE
Interpretation of the example message H (, start of transmission)
Sensor ID W
• Averaging in seconds Sensor status P = pass
• Wind direction Wind speed 0013
• . (dot character)
• Wind speed unit T = meters per second
• Checksum (most significant digit D
• Checksum (least significant digit EH (, end of transmission)
Missing Readings
If data is missing due to a measurement problem, the WS425 AB ASCII message reports for wind speed WS425 AB WAT11 Profile
The following table lists the configurable parameters and their allowed and default values for the WS425 AB WAT11 profile.
WMT700 User Guide
M211095EN-H
150

Table 54 Configurable Parameters for WS425 AB WAT11 Profile


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   79   80   81   82   83   84   85   86   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Harley Davidson
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha