User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page8/125
Date24.02.2019
Size8.38 Kb.
1   ...   4   5   6   7   8   9   10   11   ...   125
Option
Hardware Interface
A
RS-485 isolated (1 pair)
B
RS-422 isolated
C
RS-232 isolated
D
SDI-12 isolated
To change the product version characteristics listed in Table 8 (page 20)
, contact Vaisala
Service Center.
WMT700 User Guide
M211095EN-H
20


2.3.5 Digital Communication Profile
Ordering option 5 defines the used communication protocol. WS425 options are usable and backwards compatible when replacing a WS425 sensor with a WMT700 unit. Other application or customer-specific user profiles are also available.
Table 9 Digital Communication Profile
Option
Communication Profile
0
WMT70 - default mode, 8, N, 1
Polled
1
WS425 - ASCII, 8, N, 1
Polled
2
WS425 - NMEA Extended (v, 8, N, Auto send 1/s
3
WS425 - SDI (v 1.3)
1200, 7, E, 1
Polled
4
WS425 - ASOS
2400, 8, N, 1
Polled
5
ROSA - MES 9600, 8, N, 1
Polled
8
AWS520 - NMEA Extended (v, 8, N, Auto send 1/s
A
MARINE1 (v 0183)
4800, 8, N, Auto sends Digital Communication Units
Ordering option 6 offers four different digital communication options.
Table 10 Digital Communication Units


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   4   5   6   7   8   9   10   11   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Harley Davidson
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha