User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page78/125
Date24.02.2019
Size8.38 Kb.
1   ...   74   75   76   77   78   79   80   81   ...   125
Byte
Description
1
Start of text
2
Sensor ID
3
Command identifier
4
Sensor status:
• P = Pass
• F = Fail
• H = Heater failure
For further information, see notes 1 and Averaged wind direction (degrees)
8-10
Wind direction (degrees) @ peak wind speed
11-12
Averaging time for wind speed and direction
13-14
Averaging time for peak wind speed and direction (seconds)
15-19
Averaged wind speed
20-24
Peak wind speed since last WA command
25
Wind speed unit:
• M = Miles per hour
• K = Knots
• L = Kilometers per hour
• T = Meters per second
26-27
Signal quality. For further information, see note Hex checksum. For further information, see note Chapter 5 – Operation
141


Byte
Description
30
End of text
31
Carriage return
32
Line feed
Example
WAP2131870503012.6014.7K99xx
Interpretation of the example message:
• Sensor ID W
Command identifier A
• Sensor status P = pass
• Averaged wind direction (degrees Wind direction (degrees) @ peak wind speed Averaging time for wind speed and direction Averaging time for peak wind speed and direction (seconds Averaged wind speed Peak wind speed since last WA command Wind speed units K = knots
• Signal quality Hex checksum (refer to note 4): xx WS425 AB NMEA Standard Profile
When the WS425 AB NMEA Standard profile is configured, WMT700 sends messages based on the configured automatic message interval. There are no operating commands available for the user.
The following table lists configurable parameters and their allowed and default values for the WS425 AB NMEA Standard profile
Table 50 Configurable Parameters for WS425 AB NMEA Standard Profile


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   74   75   76   77   78   79   80   81   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha