User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page72/125
Date24.02.2019
Size8.38 Kb.
1   ...   68   69   70   71   72   73   74   75   ...   125
(optional) > OK. Close the New Connection Properties window. Select View > Font > Terminal.
10. Select Call > Call. Enter a name and select an icon for the connection. Select OK.
11. Switch the sensor power supply on. The following information is displayed
WMT700
v
12. Wait for 4 seconds. WMT700 enters measurement mode automatically. To test the connection, enter configuration mode with the following command:
$0OPEN
14. Use the following command to return to measurement mode
CLOSE
You can now start operating WMT700. Note that WMT700 does not send data messages automatically unless configured to do so.
WMT700 User Guide
M211095EN-H
134


More Information
‣ Measurement Mode Commands (page Communicating with Terminal Software (page Data Messages (page 119)
5.20 Entering Configuration Mode
This command switches the serial port to configuration mode. The command works with any communication profile supported by WMT700.
$aOPEN
$
Fixed text a
Value of the address parameter. If the value is 0, it refers to any WMT700 address

Carriage return

Line feed F/G ASOS Profile
The following table lists the configurable parameters and their allowed and default values for the WS425 F/G ASOS profile.
Table 47 Configurable Parameters for WS425 F/G ASOS Profile


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   68   69   70   71   72   73   74   75   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Harley Davidson
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha