User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page56/125
Date24.02.2019
Size8.38 Kb.
1   ...   52   53   54   55   56   57   58   59   ...   125
Bit
Description
0
Temperature sensor 1 failure
1
Temperature sensor 2 failure
2
Temperature sensor 3 failure
3
Heater failure. Incorrect heater element resistance
4
Too high (Vh > 40 V or Vi > 40 V) supply voltage
5
Too low (Vh < 20 V or Vi < 10 V) supply voltage
Chapter 5 – Operation
113


Bit
Description
6
Wind speed exceeds operating limits.
7
Sonic temperature exceeds operating limits.
8
Wind measurement fails over 80% of the averaging time. Reported wind is still correct.
9
Not used
10
Blocked sensor. Reported wind is still correct.
11
High noise level
12
Message received correctly. The value is always The status flags are set when an event is detected. The flags are cleared when a status message is reported. To get the current situation, you must read the status message twice.
The first status message shows all events since the last read. The second status message shows the current situation.
Example
WMT700 User Guide
M211095EN-H
114


5.9.3 Loading Settings from Configuration Files
You can configure configuration of WMT700 settings over the RS, RS, or RS-232
interface using configuration files. You can send a text file containing the configuration settings to the sensor with a terminal program, such as Tera Term or Windows
HyperTerminal.
1. Use the


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   52   53   54   55   56   57   58   59   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha