User Guide M211095en-h


WIND_GETFetches wind calibration information.More Information



Download 8.38 Kb.
View original pdf
Page45/125
Date24.02.2019
Size8.38 Kb.
1   ...   41   42   43   44   45   46   47   48   ...   125
WIND_GET
Fetches wind calibration information.
More Information
‣ ERRORS — Get Error Codes and Counts (page Ordering Options (page Restoring Serial Port Settings (page 170)
5.4 Parameter Handling Commands
All the commands in the configuration mode are in the following form:
>CMD x,y
>
Configuration mode prompt
CMD
Command
Space x
Any parameter in Table 73 (page 187)
WMT700 User Guide
M211095EN-H
102

Comma y
Value of the parameter

Press
ENTER to activate the command.
The parameter name and allowed parameter values depend on the command. For certain commands they are optional. In the following command descriptions, WMT700
configuration mode prompt and enter are left out for clarity S — Set Parameter
The
S command defines new data messages and changes values of the WMT700
parameters.
You can also use the
S command to configure data messages.
If you try to set an invalid value fora parameter or an invalid item fora data message, the response depends on the messages parameter. If messages are enabled (messages parameter is set to 1), WMT700 responds with an error message. If the messages parameter has been set to 0, WMT700 does not send any response to set parameter command. You can also fetch the most recent error data in the configuration mode with the
ERRORS
command.
Do not switch the power supply off immediately after the


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   41   42   43   44   45   46   47   48   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha