User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page40/125
Date24.02.2019
Size8.38 Kb.
1   ...   36   37   38   39   40   41   42   43   ...   125
WMT700
Connector Pin
WMT700 Signal
Description
WS425
Connector Pin
WS425 Signal
Description
WS425
Wire Color
1
Operating Power Supply VDC
Brown
3
COM2: Rx RS232RX
10
Data in (RxD) (R) (RT-)
Blue
4
COM2: Tx-/ RS232TX
9
Data out (TxD) (T) (RT) Red
5
Heater Power Supply VDC
Gray/Pink
7
Heater Power Supply Ground 3
GND
Green
10
COM2: Communications
Ground
8
GND
Yellow
11
Operating Power Supply
Ground
1
GND
Black
14
COM2: Tx+
12
Data out (T) (RT+)
White
15
COM2: Rx+
14
Data in (R) (RT+)
Pink
The Adapter Cable for WS425 Serial (SP) does not support SDI operation Adapter Cable for WS425 Analog Frequency Output
The Adapter Cable for WS425 Analog Frequency Output (SP) can be with the
WS425 cable ZZ45204. The following table lists the adapter pin-outs and signal descriptions as they appear on their user guides for both WMT700 and WS425 connectors.
Chapter 4 – Installation
95

Table 36 Pin-Outs for WS425 Analog Frequency Output Adapter Cable


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   36   37   38   39   40   41   42   43   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha