User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page4/125
Date24.02.2019
Size8.38 Kb.
1   2   3   4   5   6   7   8   9   ...   125
Test
Setup According to
Conducted RF immunity
IEC EFT immunity
IEC Surge immunity
IEC 61000-4-5
ESD immunity
IEC High voltage (Dielectric tests)
IEC Conducted emissions
1)
CISPR Chapter 2 – Product Overview
17


Test
Setup According to
Radiated emissions
CISPR RF field immunity
IEC Insulation resistance
IEC 60092-504
1)
Limits according to IEC 60945: Maritime navigation and radiocommunication equipment and systems - General requirements
- Methods of testing and required test results. 4th edition, 2002-08. See
G. Certificate (page 199)
2.3 Ordering Options
Table 4 Ordering Options
Ordering Option
Number
Ordering Option
1
Measurement range
2
Temperature range
3
Heating
4
Digital communication interface
5
Digital communication profile
6
Digital communication unit
7
Analog output signal for wind speed channel
8
Analog output signal for wind direction channel
9
Connection cables
10
Mounting adapters
11
Not in use
12
Accessories
13
Manuals
If required, you can change Digital Communication Interface (page 20)

2.3.5 Digital Communication Profile (page 21)

2.3.6 Digital Communication Units (page 21)

2.3.7 Analog Output Signal for Wind Speed Channel (page 21)

2.3.8 Analog Output Signal for Wind Direction Channel (page 23)
WMT700 User Guide
M211095EN-H
18




Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   2   3   4   5   6   7   8   9   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha