User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page26/125
Date24.02.2019
Size8.38 Kb.
1   ...   22   23   24   25   26   27   28   29   ...   125
More Information
‣ Aligning WMT700 (page 63)
4.6 Mounting WMT700 on Sensor
Support Armor Cross Arm Using
WMT70FIX
• 5-mm Allen key
Adjustable wrench
When mounting WMT700 on a horizontal sensor support armor cross arm using the
WMT70FIX mounting kit, place WMT700 with the array facing up or down.
WMT700 User Guide
M211095EN-H
60

Mounting WMT700 with the array facing down protects the sensor better against the accumulation of snow and interference from birds. The adapter drains located at the bottom of WMT700 prevent water from accumulating inside the mounting adapter. Make sure that the cable is firmly connected to the sensor. Attach the WMT70FIX mounting kit to the sensor support armor cross arm with the
U bolts and insert the U bolts in the slots of the mounting kit.
3. Check that the mounting kit is not tilted to either side and tighten the U bolts firmly. Haul the sensor up.
Chapter 4 – Installation
61


5. Holding the sensor from its body, run the cable through the mounting kit, and slide the sensor into the mounting kit.
WMT700 User Guide
M211095EN-H
62


6. To avoid misalignment, turn the sensor until the screw reaches the far end of the slot,
and tighten the screw.
1
WMT700 mounting screw. Tightening torque 5 Nm.
2
U-bolt and nut (M DINA) in horizontal slot. Align the sensor.
If you installed the sensor with the array facing down, configure WMT700 accordingly.


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   22   23   24   25   26   27   28   29   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Harley Davidson
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha