User Guide M211095en-h


Uunpacking................................................................... upgrading WS425.................................... 82, 86, 88V



Download 8.38 Kb.
View original pdf
Page124/125
Date24.02.2019
Size8.38 Kb.
1   ...   117   118   119   120   121   122   123   124   125
U
unpacking................................................................... upgrading WS425.................................... 82, 86, 88
V
vector averaging. 37
verifier........................................................................164
voltage................................................................77, voltage output. 131
Index
203


W
wind direction. 34, 35, 137, wind direction averaging......................................36
wind direction coasting.........................................37
wind direction offset. 63, wind direction output............................................131
wind measurement commands........................106
wind measurement on request. wind speed. 34, 35, 137, wind speed average..............................................120
wind speed output. 129
wiring............................................................................72
COM2 RS. heated WMT700..................................................77
non-heated WMT700........................................ retrofit installation. 93
WMT700 commands. 181
WMT700 NMEA MWV commands. 194
WMT700 profile commands..............................125
WS425 AB ASCII commands..........................148
WS425 AB NMEA extended commands. 145
WS425 AB SDI. 160, 161
WS425 AB WAT11
commands.............................................................151
WS425 cable.............................................................131
WS425 F/G ASOS commands. 136, 138–140
Z
zero alignment..........................................................65
zero wind verifier............................................ 27, 197
WMT700 User Guide
M211095EN-H
204


Warranty
For standard warranty terms and conditions, see www.vaisala.com/warranty
Please observe that any such warranty may not be valid in case of damage due to normal wear and tear, exceptional operating conditions, negligent handling or installation, or unauthorized modifications. Please seethe applicable supply contractor Conditions of Sale for details of the warranty for each product.
Technical Support
Contact Vaisala technical support at helpdesk@vaisala.com
. Provide at least the following supporting information:
• Product name, model, and serial number
• Name and location of the installation site
• Name and contact information of a technical person who can provide further information on the problem
For more information, see www.vaisala.com/support
Recycling
Recycle all applicable material.
Follow the statutory regulations for disposing of the product and packaging.
205


WMT700 User Guide
M211095EN-H
206


www.vaisala.com



Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   117   118   119   120   121   122   123   124   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha