User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page112/125
Date24.02.2019
Size8.38 Kb.
1   ...   108   109   110   111   112   113   114   115   ...   125
Parameter Name
Default
Value
Allowed Values
Units
Description
heaPeakPwr
200
min ... max = 0 ...
200 W
heaPeakPwr determines how many resistors are on at the same time. WMT700 has three heater resistors for each arm.
heaPeakPwr does not limit the power in the body heater of a heated version.
heaterOn
1 0 = Heater off = Automatic
Heater control. When the value is set to
1, WMT700
controls the heaters based on the temperature and other conditions.
messages
1 0 = Disabled = Enabled
Response for parameter setting.
msg1, msg2, msg3, msg4 String with a maximum of 80
characters.
User-configurable data message formats. Parameters correspond to the message identification numbers from to 4.
serial_n
Serial number for WMT700.
This is a read-only parameter serial_pcb
Circuit board serial number.
This is a read-only parameter.
sleepTime
5 0 = Disabled 1 …
32000
s
Duration of the low-power mode in seconds. WMT700
returns automatically to normal state after this period of time has elapsed. You can also return to normal state by sending an extra space before the polling command.
startDelay
5 0 … 30
s
Defines how long WMT700
waits before activating automatic messages at startup.
wndAvg
1 0.25 Resolution 0.25
s
Averaging time for wind measurement in seconds. This parameter affects both serial communication and analog output.
wndCoast
0 0 … 100 0 Disabled m/s
Wind direction coasting threshold in meters per second. When wind speed drops below the limit, wind direction coasting is performed. Only affects the scalar averaging mode.
WMT700 User Guide
M211095EN-H
190




Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   108   109   110   111   112   113   114   115   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha