User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page111/125
Date24.02.2019
Size8.38 Kb.
1   ...   107   108   109   110   111   112   113   114   ...   125
Parameter Name
Default
Value
Allowed Values
Units
Description
com2_interf
0 0 = RS 1 = RS 2 = SDI 3 = RS-232
Interface for serial port COM2.
(The interface for serial port
COM1 cannot be changed.)
com1_paritycom2_parity 0 0 = None = Even = Odd
Parity for serial ports COM1
and COM2.Changes take effect only after reset or the
RESET
command.
com1_protocol
0 0 Protocol for serial port COM = WMT700
• 2 = WS425 F/G ASOS
• 3 = WS425 AB ASCII = WS425 AB NMEA
Standard
• 5 = WS425 AB NMEA
Extended
• 6 = WS425 AB WAT11
• 8 = MES = WMT700 NMEA MWV
com2_protocol
0 0 Protocol for serial port COM = SDI = WS425 F/G ASOS
• 3 = WS425 AB ASCII = WS425 AB NMEA
Standard
• 5 = WS425 AB NMEA
Extended
• 6 = WS425 AB WAT11
• 8 = MES 12
• 11 = WMT700 NMEA MWV
com1_stopcom2_stop
1 1 = 1 bit = 2 bits
Stop bits for serial ports COM1
and COM. Changes take effect only after reset or the
RESET command.
freqType
0 0 = Push-pull
1 = Active pull- down = Active pull- up
AOUT1 frequency output type.
Setting 1 requires external pull- up resistor. Setting 2 requires external pull-down resistor.
heaBMaxPower
150 0 = Off = On
W
heaBMaxPower sets maximum body heater power.
Setting the parameter value to disables WMT700 body heating.
Appendix D – Configuration Parameter Descriptions
189




Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   107   108   109   110   111   112   113   114   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha