User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page110/125
Date24.02.2019
Size8.38 Kb.
1   ...   106   107   108   109   110   111   112   113   ...   125
Parameter Name
Default
Value
Allowed Values
Units
Description
aout_map
0 0 =
aout1, wind speed aout 2, wind direction =
aout1, North-
South, x component aout 2, west- east, y component =
aout1, wind speed aout2, wind speed alarm
A digital output:
hi when wind speed > aout2_o
Parameter for analog outputs inroad and rail tunnel applications and crane applications. The parameter provides horizontal and direction data.
autoPort
1 1 = COM port = COM port
Serial port to which WMT700
sends automatic data messages.
autoSend
0 0 = Automatic messages disabled 1 Automatic data message number. Selects the data message format for automatic messages.
cal_date
Wind calibration date. This is a read-only parameter.
com1_baudcom2_baud
4 0 = 300 1 = 1200 2 = 2400 3 = 4800 4 = 9600 5 = 19200 6 = 38400 7 = 57600 8 = Baud rates for serial ports
COM1 and COM. Changes take effect only after reset or the
RESET command. Note that a low bit rate can affect measurement timing, if
WMT700 cannot send the data message before anew measurement starts.
com1_data com2_data
8 7 = 7 data bits = 8 data bits
Data bits for serial ports COM1
and COM. Changes take effect only after reset or the
RESET command.
com1_delaycom2_delay
20 0 … 10000
ms
COM1 and COM Response delay in milliseconds.
WMT700 User Guide
M211095EN-H
188




Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   106   107   108   109   110   111   112   113   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha