User Guide M211095en-h


SelectionOutput Configuration



Download 8.38 Kb.
View original pdf
Page11/125
Date24.02.2019
Size8.38 Kb.
1   ...   7   8   9   10   11   12   13   14   ...   125
Selection
Output Configuration
0
Disabled
A
Voltage output 20 mV/degree
0 mV = 0 degree mV = 360 degree
D
Current output 50 uA/degree
0 uA = 0 degree mA = 360 degree
Chapter 2 – Product Overview
23


Selection
Output Configuration
E
Current output 4 … 20 mA (44.444 uA/degree)
4 mA = 0 degree mA = 360 degree km/h
F
WS425 Potentiometer output of V
ref
= 0 degree of V
ref
= 360 degree
More Information
‣ Coordinate Systems Vector and Polar Calculations (page 34)
2.3.9 Connection Cables
Ordering option 9 defines connection cables.
Table 13 Connection Cables
Selection
Cable type
1
No cables
2
Cable 2 m, cable connector, open leads on one end
3
Cable 10 m, cable connector, open leads on one end
4
MAWS cable 10 m
5
AWS520 cable 10 m. Shield connected to PE pin
6
Adapter cable for WS425 serial
7
Adapter cable for WS425 analog frequency output
8
RS485 cable 2 m, cable connector, open leads on one end
9
RS485 Cable 10 m, cable connector, open leads on one end
A
Adapter cable for WS425 analog voltage output
B
AWS520 cable 10 m. Shield not connected to PE pin.
C
ROSA analog cable 10 m, cable connector, open leads on one end
D
Junction Box with Cable 2 m
E
Cable 15 m, cable connector, open leads on one end
F
Cable 26 m, cable connector, open leads on one end Mounting Adapters
Ordering option 10 defines mounting adapters.
WMT700 User Guide
M211095EN-H
24

Table 14 Mounting Adapters


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   7   8   9   10   11   12   13   14   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha