User Guide M211095en-h


PropertyDescription/Value



Download 8.38 Kb.
View original pdf
Page102/125
Date24.02.2019
Size8.38 Kb.
1   ...   98   99   100   101   102   103   104   105   ...   125
Property
Description/Value
Readout update interval
Maximum 4 Hz
Units available ms, knots, mph, km/h, V, mA, Hz
Operating mode
Automatic message or poll mode
Virtual temperature
Celsius degrees
Digital outputs
Communication interfaces
COM1: RS
‑485
COM2: RS, RS, RS, SDI‑12
Communication profiles
WMT700, WS425 ASCII, NMEA Standard and
Extended (version 0183), SDI (version 1.3), WS425
ASOS, ROSA - MES, Customized
Bit rate, 1200, 2400, 4800, 9600, 19200, 38400, or Available averages
Maximum 3600 s
WMT700 User Guide
M211095EN-H
174


Property
Description/Value
Analog outputs for wind speed
Frequency push-pull
Pulse 0 V V 0 ... 2 kHz (f = 10 Hz/m/s) (load > 10
kohm)
Frequency pull-down
Pulse 0.5 V/V
in
-2 V (11 V minimum ... 750 Hz (load 50 kohm ±20 Frequency pull-up
Pulse 1.5 V/V
in
-4 V (8 V minimum):
Voltage
0 ... 10 V (U = 100 mV /m/s)
Current
0 ... 20 mA (I = 0.2 mA/m/s)


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Parameter name
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   98   99   100   101   102   103   104   105   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha