User Guide M211095en-h



Download 8.38 Kb.
View original pdf
Page100/125
Date24.02.2019
Size8.38 Kb.
1   ...   96   97   98   99   100   101   102   103   ...   125
Parameter Name
Default Value
Description
com1_baudcom2_baud
4 4 = 9600 bauds per second com1_data com2_data
8
Number of data bits com1_delay com2_delay
20
Response delay in milliseconds com2_interf
0 0 = RS-485
com1_parity com2_parity
0 0 = None com1_protocol com2_protocol
0
WMT700 protocol com1_stop com2_stop
1
Number of stop bits
The serial port settings have now been restored to known values. You can write the
OPEN command and start configuring WMT700.
More Information
‣ Configuration (page Chapter 7 – Troubleshooting
171


WMT700 User Guide
M211095EN-H
172


8. Technical Data Measuring Specifications
Table 59 WMT700 Wind Speed Measuring Specifications
Property
Description/Value
Observation range
WMT701: 0 ... 40 ms (89 mph)
WMT702: 0 ... 65 ms (145 mph)
WMT703: 0 ... 75 ms (168 mph)
WMT704: 0 ... 90 ms (201 mph)
Starting threshold ms (0.0223 mph)
Resolution
0.01 ms (0.0223 mph)
Response time ms
Accuracy
0 ... 75 ms (168 mph) ±0.1 ms or 2% of reading,
whichever is greater ... 90 ms (201 mph ±5% of reading
Available variables
Instant, peak, average, maximum, minimum, gust, lull
Table 60 WMT700 Wind Direction Measuring Specifications


Document code
Testsetup according to
More information
Optiontemperature range
Optionheating
Optionhardware interface
Optionunit used
Optionoutput configuration
Selectionoutput configuration
Optionadapter type
Optionaccessories
Order codedescription
Aout1 selected option
Output signal
Swnddiroffset,(angle)
Parameterdefinition
Power supplywire colors
Used heating option
Heating option
Wire type/cable length
Descriptionspare part item
Wmt700connector pin
Open commandto activate the command, press enter
Commanddescription
Wind_getfetches wind calibration information.more information
S command. power must be on for at least 5 seconds after the s
Startcommand.more information
Itemdescription
Bitdescription
G command to fetch the current wmt700 parameters. disable error messages with the command s messages,0
Errors. if all values are valid, wmt700 sends the following response:0,0,0,0you can also use the g
Data message number
Ws425 and sdi messages
Parametername
Parameterdefault
Start command.to stop measurement, use the stop
Wb,wfirmware
Wf output:wff6785672109876.5432.1k99xx5.21.2 ws425 f/g asos data messagewmt700 responds to the wa
Bytedescription
Parameterdefault value
Id character
Wx command with a character fixed-length data message.character
Start command. to stop measurement, use thestop
Problemprobable cause
Error/eventcode
Propertydescription/value
Analog outputs for wind direction
Itemorder code
Configuration mode / measurement
Settingparameter
Parameter name
Start command. you can stop the measurement with the stop
Example of the command and response:
Baud........................................................................ 105clearerr
S............................................................................... 103sleep
Gget message. get parameter.........................................................104h
Jjunction box...............................................................28l



Share with your friends:
1   ...   96   97   98   99   100   101   102   103   ...   125


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Harley Davidson
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha