Microsoft Word ezshs-5120 manual doc


(Except for SHS-5120VMX model)



Download 295.49 Kb.
View original pdf
Page2/2
Date07.11.2018
Size295.49 Kb.
1   2
(Except for SHS-5120VMX model)
The emergency key is used when the door lock does not operate due to discharged batteries or a circuit problem.
An emergency keyhole is located at the bottom of the outdoor unit. Insert the key into the keyhole and rotate it to the left and to the right to release the door lock.
- Always carry one or more emergency keys, or store one in a secret place outside.
- If the emergency key is lost, it is recommended to replace the whole key cylinder unit.
Contact your local dealer. Replacement of the key cylinder unit is not a free service.
- Remove the emergency key from the keyhole after the door lock has been released, and store it in a safe place.
16


Basic Functions
This section describes the ways to initialize the information registered in the door lock, to register the password and card data, and to open or close the door.
Initialization (Password, Card, Key Tag and Remote Controller)
All registered data (password, card and key tag) are deleted. After initialization, the password is set to '12345', and the registered card and key tag data are erased.
- After initializing the registered data, reregister the card and password.
- Initialization is available while the door is open.
- The registered HA device data can not be deleted.
1. Opening the Cover (from inside)
Lightly press the battery cover and push it up,
as shown in the diagram.
2. Pressing the [Password] Button (from inside)
Press and hold the [Password] button for 5
seconds or longer.
- Successful: “Toot Toot, toot” sounds are generated.
3. Entering the Password (from outside)
Press the registered password, or '4560852580' then press the [ ] button.
- Successful: "Too t" sound is generated.
- Failed: "Toot " sound is generated.
17


Password Registration and Change
The password can be 5 12 digits number. Only one password can be registered.
Please register a new password after initialization.
Always hold the door open while registering or changing the password.
Open
1. Pressing the [Password] button (from inside)
Toot
Open the battery cover of the indoor unit and briefly press the [Password] button.
2. Entering the Current Password (from outside)
Too t, toot, toot
Enter the current password ('12345' after initialization) when the number pad is lighted,
and press the [ ] button.
18


3. Entering a New Password (from outside)
Toot, toot
Enter the new password (5 to 12 digits) and press the [ ] button.
- To prevent burglary, it is recommended to use a password of 6 digits or longer. (Only numbers between 0 and 9 can be used.)
4. Reentering a New Password (from outside)
Too t
Enter the new password again to check if the new password is accurately configured, and then press the [ ] button.
5. Checking New Password Operation (from outside)
Too t
To make sure the password has been properly registered, check the new password and close the door.
- Please refer to "Opening from Outside with a
Password" on page 27.
- To check the new password, press the door-opening sensor on the Mortise while the door is open. When the dead bolt is pushed out, check the password, referring to the procedure described in "Opening from Outside with a Password."
- Manage your password with care so that unauthorized people will not have access to it.
Regularly changing your password can reduce the risk of it being leaked.
- A registered password cannot be deleted. Change the password to a new one or initialize it to delete all registered data (password, card and key tag) and then reregister them.
19


Card and Key Tag Registration
Up to 20 cards, including the key tag, can be registered. (Only ISO14443 A Type is available.)
Registering a card or key tag is available while the door is open.
1. Pressing the [Register] Button (from inside)
Toot
Open the battery cover of the indoor unit and briefly press the [Register] button.
2. Entering the Password (from outside)
Too t, toot, toot
Enter the password when the number pad is lighted, and press the [ ] button.
3. Placing the Card or Key Tag in Contact (from outside)
Too t
Place the card or key tag to be registered on the card reader of the outdoor unit. You will know the card or key tag has been registered when a long "too t" sounds.
20


4. Confirming Card or Key Tag Registration (from outside)
Place the registered card or key tag to the card reader on the outdoor unit.
- Please refer to "Opening the Door from Outside with a Card or Key Tag" on page 28.

Registering Additional Cards
Continued Registration
To register multiple cards or key tags, lightly place another card or key tag to the card reader within 5 seconds of registering the previous card or key tag. If another card or key tag is not exposed to the card reader within 5 seconds of registering the previous card or key tag, the registration process is automatically terminated.
Registration at another Time
To register an additional card or key tag after the registration process is terminated, repeat the registration process with the card or key tag.
21


Deleting the Card or Key Tag
Registered cards cannot be individually deleted. All card information is deleted when the card delete function is selected. Previously registered cards cannot be used to open the locked door after they are deleted.
1. Pressing the [Register] Button (from inside)
Toot Toot, toot
Open the battery cover of the indoor unit and press and hold the [Register] button for 5
seconds or longer.
2. Entering the Password (from outside)
Successful: " Too t" sound is generated.
Failed: "Toot " sound is generated.
Enter the password when the number pad is lighted, and press the [ ] button.
- Register a new card after deleting the card data.
- To open the locked door from outside after deleting card data, use the registered password.
- Deleting the card or key tag is available while the door is open.
22


Remote Controller Registration
Up to two remote controllers can be registered.
1. Pressing the [Remote] Button (from inside)
Toot
Open the battery cover of the indoor unit and briefly press the [Remote] button.
2. Entering the Password (from outside)
Too t, toot, toot
Enter the password when the number pad is lighted, and press the [ ] button.
3. Pressing the [OPEN] Button (from the remote controller)
Too t
Press and hold the [OPEN] button of the remote controller to be registered for 3
seconds or longer.
- Repeat the process above when registering an additional remote controller.
- Registering a remote controller is available while the door is open.
23


4. Confirming the Remote Controller Registration (from outside)
In Automatic Locking Mode
- Briefly press the [OPEN] button on the remote controller.
In Manual Locking Mode
- When the [OPEN] button on the remote controller is pressed, the door will be locked,
or the lock will be released.
24


Deleting the Remote Controller
Registered remote controllers cannot be individually deleted. All remote controller information is deleted when the remote controller delete function is selected.
A previously registered remote controller cannot be used to open the locked door after it has been deleted.
1. Pressing the [Remote] Button (from inside)
Toot
Toot, toot
Open the battery cover of the indoor unit and press and hold the [Remote] button for
5 seconds or longer.
2. Entering the Password (from outside)
Successful: " Too t" sound is generated.
Failed: "Toot " sound is generated.
Enter the password when the number pad is lighted, and press the [ ] button.
- Register a new remote controller after deleting the remote controller data.
- To open the locked door from outside after deleting remote controller data, enter the registered password or use the registered card or emergency key.
- Deleting the remote controller is available while the door is open.
25


Wireless HA Device Registration and
Deletion
Wireless HA products from Scommtech (7000 and 8000 series or higher) are compatible with the door lock.
Please call your local dealer to register or delete the registered wireless HA device.
Refer to the operating manual of the wireless HA device to open the door using the device.
When a wireless HA device is registered, only one remote controller can be registered.
26


Opening the Door from Outside with a
Password
1. Pressing [Enter Number] button
Press the [Enter Number] button,
and the number pad is lighted.
2. Entering the Password
Successful: " Toot, toot, toot"
Failed: “Toot

Enter the password, and press the
[ ] button or the [Enter Number] button.
- The password must be entered while the number buttons are lighted. If the light is turned off, press the [Enter Number] button and reenter the password.
- If the wrong password is entered, press the [#] button to cancel the entry and start from the beginning.
- If the wrong password is entered 3 times in a row, a "toot toot toot " alarm will sound for 10 seconds and the door lock will stop operating for 1 minute. While the door is in this inactive mode, a single "toot" sound is generated every 10 seconds, and seven consecutive "toots" will sound after 1 minute. Following this, the lock is released from inactive mode.
27


Opening the Door from Outside with a
Card or Key Tag
The door can be opened from outside using a card or key tag.
Place the registered card or key tag on the card reader.
Applying the Card or Key Tag
Successful: " Too t" sound is generated.
Failed: "Toot " sound is generated.
Place the card or key tag on the card reader.
The door will be opened after
1 second.
- The card reader will operate properly when the card and key tag is placed within 30mm and 20mm of the card reader respectively.
- The recognition distance may differ depending on the card manufacturer.
- A "Toot " alarm sound is generated when an unregistered card is placed or the card is not recognized.
28


Opening the Door from Inside
Pressing the [Open/Close] Button
Too t
Press the [Open/Close] button on the indoor unit.
Pulling down the Door Lock Handle
Too t
Rotate the door lock handle of the indoor unit downward.
Rotating the Manual Open/Close Lever Right and Left
Rotate the Manual Open/Close lever on the indoor unit to the right or left to lock or unlock the door.
- This function can operate without any batteries.
29


Pressing the [OPEN] Button of the Remote Controller
Press the [OPEN] button of the remote controller.
- The door is locked or unlocked each time the
[OPEN] button of the remote controller is pressed in the manual locking mode.
Pressing the [Open Door] Button of a Wireless HA Device
The door is unlocked when the [Open Door]
button of the wireless HA device is pressed.
- This function may differ depending on the model of the wireless HA device.
30


Closing the Door from Outside
Pressing the [Enter Number] Button
Press the [Enter Number] button on the outdoor unit when the door has been opened from inside in manual locking mode.
Closing the Door from Inside
In Automatic Locking
Mode
In Manual Locking Mode
The door is automatically locked 2 seconds after closing the door.
The door is locked when the [Open/Close]
button or the [OPEN] button of the remote controller is pressed.
31


Additional Functions
Automatic/Manual Locking Setting
The automatic locking mode allows for automatic locking of the door when it is closed.
Automatic Locking Setting
Manual Locking Setting
Set the [Automatic/Manual Locking] toggle switch of the indoor unit to the 'Automatic'
position.
Set the [Automatic/Manual Locking] toggle switch of the indoor unit to the 'Manual'
position.
Difference between Automatic and Manual Modes
- Automatic Mode: The door is automatically locked 2 seconds after being closed. This mode is not activated when the batteries are completely discharged.
- Manual Mode: The door is not automatically locked after being closed. It is locked only when the [Open/Close] button of the indoor unit, the [OPEN] button of the remote controller, or the [Enter Number] button of the outdoor unit is pressed.
For security reasons, ensure that the door is locked after locking the door in the manual locking mode, since it is not automatically locked after being closed.
- The door lock is set for the automatic locking mode if the deadbolt is automatically pushed out when the door-locking sensor on the indoor unit is pressed by hand while the door is open.
- If the door remains open while the automatic locking mode is set, two alarm sounds of "too t,
too t, too t" are generated every 15 seconds.
(This alarm sound is not generated in the manual locking mode.)
- The door is automatically locked again if the closed door is not opened within 7 seconds of being unlocked using the password, card or key tag.
32


Sound Setting and Releasing
The sound that is generated when the number buttons are pressed, when the door is locked or when the locked door is unlocked, can be set according to the user's preference.
Sound Function Setting
The product is set to generate all sounds at the factory. (Set in 2 steps)
Too t
Toot
Sound Function
[0] Button: Mute
[1] Button: 1 Step
[2] Button: 2 Step
[3] Button: 3 Step
Briefly press the [Password] button on the indoor unit.
The sound function is set when the
[ ] button is pressed after the [0]
[3]
button is pressed.
Sound Function Operation
[0] Button: All sounds except the alarm sound are deactivated.
[1]
[3] Button: All sounds are activated and the sound gets louder as the step goes up.
The sound function is set in two steps after initialization.
In registration mode, sound is generated regardless of the current setting. The setting is in effect when registration is completed.
- Setting and releasing sound is available while the door is open.
- The sound of the outdoor unit is set in the optimum condition.
-
-
-
-
33


Alarm Sound/Emergency Sound
Alarm Sound (Prank Prevention Function)
This function generates an alarm sound and deactivates door lock operation when it is improperly handled from outside.
Card or Password Error
“Toot
Too t”
(for 10 seconds)
Number Pad Operation Error
“Toot
Too t”
(for 10 seconds)
This alarm will sound if an attempt is made to open the door with an invalid card, or if a wrong password is entered three times in a row.
(The alarm sound is generated, and the door lock is deactivated for 1 minute. While the door is in this inactive mode, a single "toot" sound is generated every 10 seconds and seven consecutive "toots" will sound after 1 minute.
Following this, the lock is released from inactive mode.)
This alarm will sound if the [Enter Number]
button is pressed for three times without entering the password or placing the card.
(The alarm sound is generated and the door lock is deactivated for 1 minute. While the door is in this inactive mode, a single "toot" sound is generated every 10 seconds and seven consecutive "toots" will sound after 1 minute.
Following this, the lock is released from inactive mode.)
Releasing the Alarm
[Inside]
[Outside]
Or
Press the [Open/Close] button of the indoor unit or the [OPEN] button of the remote controller, or rotate the handle downward.
Expose the registered card or key tag to the card reader, or enter the password and then press the [ ] button.
(The alarm must be released within 10
seconds of its activation.)
34


Setting the Security Function
This function prevents intrusion from outside while the residents are out. Once set, it generates an alarm sound when the door lock is operated from inside.
Too t,
Too t
Setting the
SecurityFuncti on
Activating theSecurity
Function
Releasing theSecurity
Function
Too t
Press the [Enter Number]
button on the outdoor unit so that the number pad can be lighted.
Press and hold the [#]
button on the outdoor unit for 3 seconds while the door is being locked.
Enter the password and press the [ ] button to set the security function.
The security function is automatically released when the locked door is opened from outside by entering the registered password or exposing the card or key tag to the card reader.
[Inside]
Too t, too t, too t
(for 5 minutes)
This alarm sounds if an attempt is made to open the door from inside by pressing the [Open/Close] button, or by turning the door lock handle of the indoor unit.
[Outside]
Or
Expose the registered card or key tag to the card reader, or enter the password, and then press the [ ]
button.
35


Intrusion Detection Function
This function generates the alarm sound when an attempt is made to forcefully open the door from the inside or the outside.
(This is a basic function of the lock, and cannot be separately set or released.)
“Toot
, toot
, toot

(for 5 minutes)
If the door is forcefully opened while locked, the door opening sensor detects it and generates the alarm sound.
Releasing the Emergency Sound
[Inside]
[Outside]
Or
Or
Open the battery cover of the indoor unit and take out the batteries, or press one of the registration buttons or the [OPEN] button of the remote controller.
Expose the registered card or key tag to the card reader, or enter the password and then press the [ ] button.
Fire Detection Function
This function generates the alarm sound when fire is detected so that the residence can quickly respond. (The fire detection function is a basic function of the lock, and cannot be released by the user.)
Toot
, toot
, toot
(for 15 seconds)
When fire occurs, the temperature sensor detects it and flashes the
[Open/Close] button while generating the alarm sound.
The door is automatically opened after the alarm sound has stopped.
(The door lock resumes normal operation if the inside temperature returns to a normal level.)
The fire detection function is activated when the temperature rises around 55 (sensor operating temperature of around 50 ). Actual temperature can differ depending on the installation environment.
36


Double Locking
The double locking function prevents opening of a locked door from outside.
Setting
Double
Locking
Activating
Double
Locking
Releasing
Double
Locking
[Inside]
Too t
Press the [Open/Close] button for 2 seconds or longer from the inside while the door is locked.
[Inside]
Too t,
too t
[Outside]
Too t,
too t
The double locking sound is generated when the [Open/Close] button is pressed, or the [Open] button of the remote controller is pressed.
The double locking sound is generated and the door cannot be opened when the [Enter
Number] button is pressed, or a card is applied.
[Inside]
The double locking function is released when the indoor unit handle is rotated downward, or the manual Open/Close lever is rotated to the right or left.
Please be cautious when using this function, since the door can only be opened from outside using the emergency key when the function is set. Please be particularly careful of children accidentally setting this function from inside.
37


Troubleshooting
Please refer to the following if the door lock does not operate properly. If the problem can still not be solved, contact the nearest service center.
Power Source
Problem
Solution
- Check to ensure the batteries are in good condition, with the poles (+/-) correctly placed.
- Check to see if the batteries are discharged, or have been inserted improperly.
Remark
There is no power.
P. 14 15
Password / Card or Key Tag
Problem
Solution
- This may be a case of delayed password change. The password must be changed while the number pad is lighted. Furthermore, the new password must be entered within 5 seconds of entering the previous one.
- Replace the batteries if they are discharged.
- Repeat the procedure again, referring to “Password
Registration/Change” in the user guide.
- When registering multiple cards and key tags continuously,
the next card or key tag must be placed on the card reader within 5 seconds of the previous card or key tag.
- Check that the registered password has been correctly entered.
- If the light of the number pad turns out while the password is being entered, then the entry will not be accepted.
Reenter the password from the beginning when the number pad is lighted again after pressing the [Enter
Number] button. (The light of the number pad is automatically turned off if an entry is not initiated within 5
seconds.)
- This may be a case of an unregistered card or key tag being used, or of the card or key tag not being recognized. Register the card or key tag, and try to open it again.
- The card or key tag must be properly placed on the card reader.
Remark
The password cannot be changed.
P. 18 19
The card or key tag cannot be registered.
P. 20 21
The door cannot be opened even after entering the password followed by the [ ] button.
P. 27
The door cannot be opened with a card or key tag.
P. 28 38


Password / Card or Key Tag
Problem opened with the password, card or key tag.
Solution
- The door cannot be opened from the outside using the password, card or key tag if the double locking function has been activated. If the double locking function is activated, a "too t, too t" sound is generated when the [Enter Number] button is pressed, or a card is applied.
- This could be a malfunction of the door lock. Please call the nearest service center.
Remark
P. 37
The password, card or key tag registration data can be verified, but the door cannot be opened.
-
Automatic Locking
Problem
Solution
- Check to ensure that the automatic locking mode has been set. If the operation mode is set to the manual locking mode, press the [Enter Number] button to lock the door.
- If the door does not automatically lock when in the automatic locking mode, then the door lock is installed improperly. Contact the digital door lock installer to have it reinstalled.
- The automatic locking function will not work if the batteries are completely discharged. Check the batteries.
Remark
The door does not lock automatically after being closed.
P. 32
Alarm Sound
Problem
The "too t, too t"
alarm sound is generated when the [Enter Number]
button is pressed.
A strange sound
(too t, too t, too t)
occurs when the door lock operates.
Solution
- The alarm sound is generated if the [Enter Number]
button is pressed while the double locking function is activated. Release the double locking function before using the door lock.
- It is notifying you that the batteries need to be replaced.
Please change the batteries within 1 week.
Remark
P. 37
P. 14 39


Operating Method Summary
Make sure if a door is open to initialize, register, change or delete registered data
Function
Initialization
(Password, card,
key tag and remote controller all deleted.)
Password
Registration/Change
Card or Key Tag
Registration
Card and Key Tag
Delete
Remote Controller
Registration
Remote Controller
Delete
Wireless HA Device
Registration and
Deletion
Default
Setting or Releasing
(Press the buttons in the given order.)
Press and hold the [Password]
button for 5 seconds
Enter button
-
Press thethe current password or '4560852580'
The password is set to '12345' after initialization.
Current
Password or '12345'
None buttonbuttonCurrent password entry +[Password]
buttonNew password entry +New password buttonreentry +
button[Register]Password entry +
buttonCard or key tag recognition
Press and hold the [Register]
buttonPassword entry +
button
None button for 5 seconds
None buttonbuttonPassword entry +[Remote]
Press and hold the [OPEN] button of the remote controller for 3
seconds
Press and hold the [Remote]
buttonPassword entry +
button for 5 seconds
None
None
Please call the nearest service center.
Door Lock Handle: Rotate the indoor unit door lock handle downward.
Opening the Door from Inside
-
Remote Controller: Press the [OPEN] button of the remote controller.
Wireless HA Device: Press the [Open Door] button of the wireless
HA device.
[Open/Close] button: Press the [Open/Close] button of the indoor unit.
Automatic Locking: Close the door.
-
Manual Locking: Press the [Open/Close] button or the [OPEN]
button of the remote controller.
Closing the Door from Inside
40


Function
Default
Setting or Releasing
(Press the buttons in the given order.)
Card or Key Tag: Apply the card or key tag to the reader.
Password: Press the [Enter Number] button.
Enter the
Opening the Door from Outside
- password.button
Emergency Key: Insert the emergency key in the emergency keyhole and rotate it to the right and left.
Automatic Locking: Close the door.
Manual Locking: Press the [Enter Number] button.
Place the [Automatic/Manual Locking] toggle switch in the 'Automatic' position.
Place the [Automatic/Manual Locking] toggle switch in the 'Manual'
position.
Press and hold the [Password]
button, or+
button.
Press
,
,
Closing the Door from Outside
Automatic Locking
Setting
Manual Locking
Setting
Sound Setting /
Releasing
Security Function
Setting
-
Automatic
Locking
2 (“Setting”)
-
Press the [Enter Number] button while the door is locked.
button for 3 secondsEnter thePress and hold the buttonpassword +
Enter the password or place the card or key tag.
Press one of the registration buttons, or the [OPEN] button of the remote controller.
Security Function
Release
Emergency Sound
Deactivation from
Inside
Emergency Sound
Deactivation from
Outside
Double Locking
Setting
Double Locking
Release
-
-
-
Enter the password or place the card or key tag.
Press and hold the [Open/Close] button for 2 seconds or longer while the door is locked.
Rotate the indoor unit handle downward.
41


Product Specifications
Item
Voltage
Emergency Power
Source
Operation Method
Weight
Product Dimensions
Specifications
8 AA Alkaline 1.5 Batteries (LR6) (6V)
9V Battery (6LF22) (Separately purchased)
Electronic Control Method (Password entry or card or key tag reading)
2.6Kg (including both indoor and outdoor units)
Outdoor Unit
(including the handle)
Indoor Unit
(including the handle)
Key Tag
82 mm(W)×299mm(H)×65.5 mm(D)
78 mm(W)×318 mm(H)×78 mm(D)
23.5 mm(W)×54 mm(H)×6 mm(D)
The content of this manual is subject to change without prior notice to the user in order to enhance performance of the product.
Product Name (Model Wireless device using
Name)extremely low power radio
(SHS-5120)
Certificate Number
Trade Name of
Certificate Grantee
Country of
Manufacturing
SCT-SHS-5120
Seoul Commtech
Republic of Korea
42



Share with your friends:
1   2


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
yamaha