Iq force™ Gas Detector Reference Manual



Download 339.9 Kb.
View original pdf
Page86/87
Date11.05.2019
Size339.9 Kb.
1   ...   79   80   81   82   83   84   85   86   87
Sensor
CO
H
2
S
SO
2
NO
NO
2
Cl
2
ClO
2
H
2
HCN
HCl
NH
3
C
2
H
4
C
2
H
2
Carbon monoxide (CO)
100
<1
<1 5
<1
-1
-3 50 15 3
0 25 250
Carbon monoxide (CO-H)
100
<1
<1
<1
<1
<1
ND
5
<1
ND
0
<30 100
Hydrogen sulfide (H2S)
<2 100
<10
<4
-20
-25
-50
<1
ND
ND
<1
<1
ND


53
IQ Force Error Codes
IQ Force™ Gas Detector Reference Manual Appendix
Appendix E IQ Force Error Codes
Error
code
Description
Course of Action
003
Inconsistency in memory storing instrument configuration
Contact factory or local service center
004
Inconsistency in memory storing O sensor configuration
Contact factory or local service center
005
Inconsistency in memory storing LEL sensor configuration
Contact factory or local service center
006
Inconsistency in memory storing CO sensor configuration
Contact factory or local service center
007
Inconsistency in memory storing HS sensor configuration
Contact factory or local service center
008
Inconsistency in datalogger memory
Download then clear datalogger in
Biotrak. If error persists, contact factory or service center.
009
One of the installed sensors does not match the sensor configuration in Biotrak
Check installed sensors and Biotrak configuration
010
No sensors installed
Install sensors) and configure in Biotrak
Error
code
Description
Course of Action
012
Instrument cannot read temperature which is required for accurate gas readings
Contact factory or local service center
014
Vibrating alarm doesn’t work
Contact factory or local service center
015
O2 sensor configured in Biotrak but not found in instrument
Check installed sensors and Biotrak configuration
016
LEL sensor configured in Biotrak but not found in instrument
Check installed sensors and Biotrak configuration
017
Type of toxic sensor configured in Biotrak not found in instrument
Check installed sensors and Biotrak configuration
025
O2 sensor found in instrument but not configured in Biotrak
Check installed sensors and Biotrak configuration
026
LEL sensor found in instrument but not configured in Biotrak
Check installed sensors and Biotrak configuration
027
Toxic sensor found in instrument but not configured in Biotrak
Check installed sensors and Biotrak configuration





Revision August 2012
© 2012 Honeywell Analytics. All rights reserved.
http://www.gastech.com.au
24 Baretta Rd
Wangara Western Australia 6065
GasTech Australia Pty Ltd Fax 1800 999 903 Tel 1800 999 902



Iq force™ gas detector
Contacting honeywell analytics
Technical services
Appendix a toxic gas measurement – warning, danger, stel,
Appendix d toxic sensor cross-sensitivity .............................. 52
Operating temperature
Multi-sensor capability
Table 2. alarm logic
Iq force portable gas detectors have been designed for the
In the event of an lel over-range alarm, the iq force must be
A sensor that cannot be calibrated or is found to be out of toler-
Do not use the pump for prolonged periods in an atmosphere
Case: the instrument is enclosed in a solid pc (polycarbonate) case with tpe (rubber) overmold.2. front face:
On/off mode button:
Battery charger connector:
Turning the iq force on
Notethe bump test interval and bump test due reminder are
Notesample probe assembly and tubing must be attached when
Always verify that all sensors present in the instrument are
Turning the iq force off
The iq force is designed to detect potentially life threatening
The iq force must be located in a nonhazardous location during
A combustible sensor over-range alarm indicates a potentially
Pc connection via infrared port
Error messages
Manual sample-draw kit
Motorized sample-draw pump
The canadian standards association (csa) requires the lel
Calibration/accuracy verification
Figure 1. bump test/span calibration setup
Fresh air/zero calibration
Possible causes and solutions
Fresh air/zero calibrations may only be performed in an
Span calibration
Noteonce the calibration cycle is completed, the iq force will
Possible causes of span calibration failure and remedies:
A sensor that cannot be calibrated or is found to be out of
Noteto enable the h
Notehoneywell analytics recommends regular verification of
Notethe bump test interval and bump test reminder are used
Toxic gas measurement – warning, danger, stel, and twa alarms
A.2 time weighted average (twa)
Appendix b calibration frequency rec-
Verification of accuracy & related terminology
Lengthening the intervals between calibration checks or bump tests
One button automatic full calibration and calibration docks
Iq force sensor information



Share with your friends:
1   ...   79   80   81   82   83   84   85   86   87


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Harley Davidson
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
Xperia
yamaha