Azur 40r av receiver User’s manual Azur av receiver



Download 277.54 Kb.
View original pdf
Page1/4
Date29.09.2018
Size277.54 Kb.
  1   2   3   4

azur R V2.0
AV receiver
User’s manual


2 Azur AV receiver
Introduction Limited warranty Safety precautions Important safety instructions Front panel connections Rear panel connections Remote control Surround Sound modes Loudspeaker positioning Loudspeaker connections Audio connections Video connections Digital connections ..................................................................................18 6.1 Direct In .. ...........................................................................................18 6.1 Preamp Out Front Input connections Aerial connections Onscreen display (OSD) ..........................................................................20
OSD menus Surround Sound setup Operating instructions Custom installation use ...........................................................................28
Reset/Back-up memory Troubleshooting Technical Specifications ..........................................................................30
CONTENTS

In addition, the RV also carries a 6.1 channel analogue input.
This feature allows for the connection of a DVD Audio or SACD player equipped with a 5.1/6.1 output. This means that the RV is fully equipped to make the most of these exciting new music formats.
As well as the full complement of audio inputs, the RV also performs Composite, S-Video and Component Video switching. This means that the RV can be used as a hub to route video signals in addition to the audio ones.
All this proprietary engineering is housed within our low resonance,
acoustically damped chassis. An Azur Navigator remote control is also provided, giving full remote control of your AV receiver in an attractive and easy to use handset.
Your RV can only be as good as the system it is connected to.
Please do not compromise on your speakers or cabling. Naturally we particularly recommend DVD/CD players or other source equipment from the Cambridge Audio Azur range, which have been designed to the same exacting standards as our receivers. Your dealer can also supply excellent quality Cambridge Audio interconnects to ensure your system realises its full potential.
Thanks for taking the time to read this manual, we do recommend you keep it for future reference.
Matthew Bramble
Technical Director
540R V AV receiver
Azur AV receiver Thank you for purchasing this Cambridge Audio Azur range AV receiver.
This R version 2 is part of our commitment to the ongoing development of the Azur range. We hope that you will appreciate the results and enjoy many years of listening pleasure from it.
About the R V2.0
The RV is designed to maximise multi-channel performance without compromising on stereo reproduction. As such, the six 80W
discrete amplifiers are kept as separate as possible from the processing and input stages. An oversized power supply ensures that the RV can maintain a high power output into even difficult speaker loads to ensure a powerful and effortless sound. For this V model we have fitted an improved volume control IC, larger
PSU capacitors and made various improvements to the circuitry further elevating the sound quality of the unit. The Video switching has also been completely redesigned to give higher bandwidth compatible with
HDTV and the unit now features full On Screen Display.
A full range of digital and analog inputs are fitted to the R V2.0.
Digital inputs allow for the connection of suitably equipped DVD players,
satellite boxes and games consoles for decoding into stereo or digital surround formats. Conventional analog stereo inputs allow the connection of CD players and the like to ensure the best possible stereo reproduction. The RV is also capable of decoding analog stereo sources in Dolby Pro Logic
®
II and DTS Neo:6, fora convincing and effective surround experience from an analog source. This ensures sources such as analog televisions and VCRs can also make full use of the RVs surround capabilities.
INTRODUCTION


4 Azur AV receiver
Cambridge Audio warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below).
Cambridge Audio will repair or replace (at Cambridge Audio's option) this product or any defective parts in this product. Warranty periods may vary from country to country. If in doubt consult your dealer and ensure that you retain proof of purchase.
To obtain warranty service, please contact the Cambridge Audio authorised dealer from which you purchased this product. If your dealer is not equipped to perform the repair of your Cambridge Audio product,
it can be returned by your dealer to Cambridge Audio or an authorised
Cambridge Audio service agent. You will need to ship this product in either its original packaging or packaging affording an equal degree of protection.
Proof of purchase in the form of a bill of sale or receipted invoice, which is evidence that this product is within the warranty period, must be presented to obtain warranty service.
This Warranty is invalid if (a) the factory-applied serial number has been altered or removed from this product orb) this product was not purchased from a Cambridge Audio authorised dealer. You may call
Cambridge Audio or your local country Cambridge Audio distributor to confirm that you have an unaltered serial number and/or you purchased from a Cambridge Audio authorised dealer.
This Warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of, or to any part of, the product. This Warranty does not cover damage due to improper operation, maintenance or installation,
or attempted repair by anyone other than Cambridge Audio or a
Cambridge Audio dealer, or authorised service agent which is authorised to do Cambridge Audio warranty work. Any unauthorised repairs will void this Warranty. This Warranty does not cover products sold AS IS or WITH
ALL FAULTS.
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY
ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. CAMBRIDGE AUDIO
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BYLAW, THIS
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND
IMPLIED WARRANTIES WHATSOEVER INCLUDING, BUT NOT LIMITED TO,
THE WARRANTY OF MERCHANTABILITY AND FITNESS FORA PRACTICAL
PURPOSE.
Some countries and US states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other statutory rights, which vary from state to state or country to country.
LIMITED WARRANTY

RV AV receiver
Azur AV receiver Checking the Power Supply Rating
For your own safety please read the following instructions carefully before attempting to connect this unit to the mains.
Check that the rear of your unit indicates the correct supply voltage. If your mains supply voltage is different, consult your dealer.
This unit is designed to operate only on the supply voltage and type that is indicated on the rear panel of the unit. Connecting to other power sources may damage the unit.
This equipment must be switched off when not in use and must not be used unless correctly earthed. To reduce the risk of electric shock, do not remove the unit's cover (or back. There are no user serviceable parts inside. Refer servicing to qualified service personnel. If the power cord is fitted with a moulded mains plug the unit must not be used if the plastic fuse carrier is not in place. Should you lose the fuse carrier the correct part must be reordered from your Cambridge Audio dealer.
The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-insulated
‘dangerous voltage within the product’s enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the service literature relevant to this appliance.
This product complies with European Low Voltage (73/23/EEC)
and Electromagnetic Compatibility (EEC) Directives when used and installed according to this instruction manual. For continued compliance only Cambridge Audio accessories should be used with this product and servicing must be referred to qualified service personnel.
The crossed-out wheeled bin is the European Union symbol for indicating separate collection for electrical and electronic equipment. This product contains electrical and electronic equipment which should be reused, recycled or recovered and should not be disposed of with unsorted regular waste. Please return the unit or contact the authorised dealer from whom you purchased this product for more information.
Plug Fitting Instructions (UK Only)
The cord supplied with this appliance is factory fitted with a UK mains plug fitted with a 5 amp fuse inside. If it is necessary to change the fuse, it is important that a 5 amp one is used. If the plug needs to be changed because it is not suitable for your socket, or becomes damaged, it should be cutoff and an appropriate plug fitted following the wiring instructions below. The plug must then be disposed of safely, as insertion into a mains socket is likely to cause an electrical hazard.
Should it be necessary to fit a pin BS mains plug to the power cord the wires should befitted as shown in this diagram. The colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug. Connect them as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter Nor coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
The wire which is coloured GREEN/YELLOW
must be connected to the terminal which is marked with the letter E or coloured GREEN.
If your model does not have an earth wire, then disregard this instruction.
If a standard amp (BS 1363) plug is used, a 5 amp fuse must befitted, or if any other type of plug is used a 5 amp fuse must befitted, either in the plug or adaptor,
or on the distribution board. SAFETY PRECAUTIONS


6 Azur AV receiver
Please take a moment to read these notes before installing your RV, as they will enable you to get the best performance and prolong the life of the unit. Please retain these instructions for future reference.
Ventilation
IMPORTANT - The unit will become hot when in use. Please ensure that there is ample ventilation around the unit. Leave at least cm of space between the top, back and sides. Do not situate it on a rug or other soft surface and do not obstruct the air inlet and outlet grilles on the underside and top cover. Do not place in an enclosed area such as a bookcase or in a cabinet.
Positioning
Choose the installation location carefully. Avoid placing it indirect sunlight or close to a source of heat. Also avoid locations subject to vibration and excessive dust, cold or moisture. Do not place the unit on an unstable surface or shelf. The unit may fall, causing serious injury to a child or adult as well as serious damage to the product. Do not place a CD player or other equipment on top of the unit.
This unit must not be exposed to dripping or splashing water or other liquids. No objects filled with liquid, such as vases, shall be placed on the unit. In the event, switch off immediately, disconnect from the mains supply and contact your dealer for advice.
Ensure that small objects do not fall through any ventilation grille. If this happens, switch off immediately, disconnect from the mains supply and contact your dealer for advice.
Electronic audio components have a running in period of around a week
(if used several hours per day. This will allow the new components to settle down, the sonic properties will improve over this time.
Grounding and polarisation
The unit maybe equipped with a polarised alternating current line plug
(a plug having one blade wider than the other. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarised plug. (North
America Only)
Power sources
The unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power- supply to your home, consult your product dealer or local Power
Company. This unit has been designed to be left in Standby mode when not in use,
this will increase the life of the amplifier (this is true with all electronic equipment. If you do not intend to use this unit fora long period of time,
unplug it from the mains socket.
Power cord protection
Your power supply cord should be placed so that the power lead is not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to cords at wall plugs and where the power lead exits from the unit.
Be sure to insert each power cord securely. To prevent hum and noise,
do not bundle the interconnect leads with the power cord or speaker leads.
IMPORTANT SAFETY INSTRUCTIONS

RV AV receiver
Azur AV receiver Overloading Do not overload wall outlets or extension cord as this can result in a risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard. Lightning For added protection during a thunderstorm, or when it is left unattended and unused for long period of time, unplug the unit from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit from lightning and power-line surges.
Outdoor antenna grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section of the National Electrical Code, ANSI/NIPA No. 70-1984 (section of Canadian Electrical Code, Part 1) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
Cleaning
Unplug the unit from the wall outlet before cleaning. To clean, wipe its case with a moist, lint-free cloth. Do not use any cleaning fluids containing alcohol, ammonia or abrasives. Do not spray an aerosol at or near the unit.
Attachments
Do not use attachments not recommended by your dealer as they may cause harm to the unit.
Servicing
These units are not user serviceable, never attempt to repair,
disassemble or reconstruct the unit if there seems to be a problem. A
serious electric shock could result if this precautionary measure is ignored. In the event of a problem or failure, please contact your dealer.
Contact the service department should any of these conditions occur- When the power-supply cord or plug is damaged- If liquid has been spilled, or objects have fallen into the amp- If the unit has been exposed to rain or water- If the unit does not operate normally after following the operation instructions, adjust only those controls that are covered by the operation instructions.
- If the unit has been dropped or damaged in anyway- When the unit exhibits a distinct negative change in performance.
IMPORTANT
If the unit is run at a very high level, a sensor will detect a temperature rise and show "PROTECTION OVERLOAD" on the display. The unit will then go into Standby mode. It cannot be switched on again until the temperature has fallen to a more normal level.


8 Azur AV receiver
Standby/On
Switches the unit between Standby mode (indicated by dim power LED)
and On (indicated by bright power LED. Standby is a low power mode where the power consumption is less than 10 Watts. The unit should be left in Standby mode when not in use.
Phones
Allows for the connection of stereo headphones with a ¼" Jack plug.
Headphones with an impedance of between 32 and 600 ohms are recommended.
Tuning +Used to tune FM frequencies and skip presets in Tuner mode.
Mode/Store
Press to cycle between Tuner modes (refer to the ‘Operating
Instructions’ of this manual for more information).
Stereo
Press to listen to a source in either analog stereo or digital (LPCM)
stereo (depending on the input mode) from the front left and right loudspeakers only.
Dolby Digital EX / DTS ES
Press to select between various standard Dolby Digital or DTS surround modes (with suitably encoded digital source material. Also selects extended Dolby Digital EX and DTS ES modes which provide 6.1 output with suitably encoded EXES material. These modes can only be decoded from digital audio sources (via Coaxial or Optical inputs. An
Autodetect mode is also available which allows the RV to automatically set itself to the appropriate mode for digital material.
Volume
Phones
Tuning
Mode/Store
DVD
Video Dolby Digital EX/
DTS ES
DSP
Mode
Pro Logic II/
Neo Input
Mode
Video 3 inputs
Video
Left
Right
Stereo
Video Video Tuner FM/AM Tape/MD/CDR
CD/Aux
6.1 Direct

+
Standby / On azur
540R
AV Receiver
FRONT PANEL CONTROLS 2
3 5
1 2
3 4
5 6
7 8
9 10 11 12 13 14 15 16 17 18 19 20 4
6

RV AV receiver
Azur AV receiver Pro Logic II / Neo:6
Press to decode suitable encoded analog stereo source material into surround sound. Autodetection for these modes is not possible and they must be manually selected.
DSP Mode
The RV can create a surround sound effect even from non- encoded material by Digital Signal Processing (DSP). Press this button to choose one of the following surround sound effects THEATER, HALL,
MOVIE, MUSIC or ROOM.
Input Mode
Press this button to toggle between analog or optical/coaxial digital input types for the currently selected source. The RV remembers the input type selected for each source when you return to that source.
DVD
Press to select the DVD source equipment for output through the 540R
V2.0.
Video Press to select the source equipment connected to Video 1 for output through the R V2.0.
Video Press to select the source equipment connected to Video 2 for output through the R V2.0.
Video Press to select the source equipment connected to Video 3 (on the front panel) for output through the R V2.0.
Tuner FM/AM
Press to select the tuner for output through the RV. In Tuner mode also use this button to switch between FM and AM modes.
Tape/MD/CDR
Press to select the recording device connected to the Tape/MD/CDR
input for output through the R V2.0.
CD/Aux
Press to select the CD or other source equipment connected to CD/Aux on the rear panel for output through the RV Direct
Press to select a 5.1 or 6.1 DVD-A or SACD player connected to the Direct In sockets.
Infrared sensor
Receives IR commands from the supplied Azur remote control. A clear unobstructed line of sight between the remote control and the sensor is required.
Volume
Use to increase/decrease the level of the sound from the outputs of the
540R V2.0.
Video 3 input sockets
Allows a video camera recorder/video games console to be connected and selected by the Video 3 source button 8
10 9
11 15 16 17 18 19 12 13 14 20


10 Azur AV receiver
FM/AM antenna
All tuner antenna connections are made here. Refer to the ‘Antenna
Connections’ section of this manual for more information.
TV/Mon outputs
S-Video - Connect to your television via S-Video cable to display the picture of any S-Video connected unit.
Composite - Connect to your television via RCA phono cable to display the picture of any composite video connected unit.
These outputs are also used to view the RVs onscreen setup menu.
S-Video inputs
Connect the S-Video outputs from the source equipment.
Composite Video inputs
Connect the Composite Video outputs from the source equipment.
Component Video inputs
Connect the Component Video outputs from the source equipment.
Note: The preferred connection method for video sources is always
Component Video (highest quality) then S-Video then Composite Video.
DVD Component Video sources often also support Progressive Scan which gives better picture quality if supported by both your DVD player and TV.
Component Video Out
Connect to the Cr/Pr, Cb/Pb, & Y terminals of a television set.
Note: There is no onscreen setup menu present on the Component
Video outputs. Power Rating VAC 50Hz
FM 75

AM
Loop
300

Video Video 1
DVD
Sur
Left
Sur
Right
Sur
Back
Left
Right
Centre
Reset
Power
On
Off
Tape Play
Tape Rec
CD
DVD
CD/Aux
Video Video 1
DVD
CD
Video Video 2
DVD
Video Video 1
DVD
SB
SB
SW
SW
Cen
C
SR
SR
R
R
SL
SL
L
L
Power AC
Max Power Consumption W Direct In Preamp Out
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Component Video In
DVD
Video Video 2
Tuner
RS232C
S-Video In
Optical In
Composite Video In
Audio In
Tape
L
R
L
R
Coax In
Coax In
Coax Out
Optical
Out
Component Video Out
Risk of electric shock
Do not open
Caution / Avis /Achtung
Risque de choc electrique
Ne pas ouvrir
Vorm öffnen des gërates
Netzstecker ziehen www.cambridge-audio.com
Designed in London, England
Speaker Impedance 4-8 Ohms
Video Video 2
Control
Bus
This device complies with part 15 of FCC rules
Manufactured in an ISO9002
approved facility
TV/Mon Out
S-Video
Com posit e
azur R V2.0
AV Receiver
Serial No. label fitted on underside
In
REAR PANEL CONNECTIONS 1
2 3
4 7
9 8
10 11 5
6 12 13 14 15 16 17 18 19 20 2
3 4
5 6

RV AV receiver
Azur AV receiver Optical In
Connect to the digital optical (Toslink) outputs from source equipment.
Optical Out
Connect to the digital optical (Toslink) input of an external recording device (eg MD/CDR etc) to record from the selected digital audio source.
Coax In
Connect to the digital coaxial (SPDIF) outputs from source equipment.
Coax Out
Connect to the digital coaxial (SPDIF) input of an external recording device (eg MD/CDR etc) to record from the selected digital audio source. Control Bus In
Allows un-modulated commands from multi-room systems or other components to be received by the R V2.0.
Reset
Resets all factory default settings. Refer to the ‘Reset/Back-up memory’
section of this manual for more information.
Power On/Off
Switches the unit on and off.
Mains power lead
Once you have completed all connections, plug the AC power lead into an appropriate mains socket. The AV receiver is now ready for use.
Speaker terminals
Connect to loudspeakers with an impedance of between 4-8 ohms Preamp Out
Connect to the 6.1 (or 5.1) channel input terminals of another amplifier system, separate power amps, subwoofer or active loudspeakers Direct In
Connect to the 6.1 (or 5.1) channel output terminals of a DVD player with built-in surround sound decoding for playing DVD-A or SACD.
Tape
Connect the Tape Play sockets to the line output terminals of a Tape deck, MD player, CD-R etc. Connect the Tape Rec sockets to the line input terminals of a Tape deck, MD player, CD-R etc.
Audio inputs Connect to the audio line output terminals of a source device (eg CD,
DVD player etc).
RS232C
For use by an installer/dealer for software updates 14 15 16 17 18 19 20 8
9 10 11 12 13

CH Select
Press to select individual channels, then use volume to balance speakers.
Sub On/Off
Press to turn on/off the output of the subwoofer.
Delay
Press to set the delay times when setting up surround sound speakers.
SPK Setup
Press to change the surround sound speaker settings.
On-screen Display (OSD)
Press to access an onscreen setup menu when connected to a monitor/screen via composite or S-video connections.
Mute
Mutes the audio on the AV Receiver. The mute mode is indicated by the channel LED flashing. Press again to cancel mute.
Volume
Increase or decrease the volume of the AV receiver output. Also used as up/down in the OSD setup menu Azur AV receiver
REMOTE CONTROL
The RV is supplied with an Azur Navigator remote control.
Insert the supplied AAA batteries to activate. For full details of the various adjustment functions available from the remote, refer to the later sections of this manual.
Standby/On
Switches the unit between On and Standby mode.
Input Mode
Switches the RV between analog and digital inputs for the currently selected source.
Stereo, PLII/NEO 6, DD EX/DTS ES, DSP Mode
See button details as listed in the Front Panel Controls section.
Dynamic
Press repeatedly to reach the desired dynamic compression range
(Dolby Digital mode only).
LFE Trim
Press to access the Low Frequency Trim (subwoofer) mode.
Test Tone
Press to access the test tones to balance your surround sound speakers.
Stereo
Input
Mode
6.1
Direct
DSP
Mode
Dynamic
PL II
Neo DD EX
DTS ES
Test
Tone
CH
Select
LFE
Trim
Sub
On/Off
Delay
Tuner
AM/FM
Bass
Treble
Mode
Store
Stereo
Mono
Display
PTY
APS
SPK
Setup
DVD
Video Video Video 3
CD
Aux
Tape
MD/CDR
Enter
Vol
Vol


Tune
Press the right arrow to increase tuner frequency/change preset. Press the left arrow to decrease tuner frequency/change preset. Also used to scroll left/right in the OSD setup menu.
Enter
Used in the OSD setup menu Direct
Selects the 5.1/6.1 Direct input.
Bass Treble
Press for bass/treble adjustment, using the Volume up/down buttons.
PTY (Program Type Search)
Press to search by program type when in Tuner mode.
APS (Auto Program Search)
Allocates and memorises radio stations automatically.
Display
When listening to source equipment press to view the input type
(optical/coaxial or analog. When listening to FM with RDS, press to view station information.
540R V AV receiver
Azur AV receiver Stereo Mono
When listening to FM, press to alternate between stereo and mono modes.
Store
Press to store the current frequency when in Tuner mode.
Mode
Press to select Auto/Manual or Preset tuning when in Tuner mode.
Tuner FM/AM, DVD, Video 1, Video 2, Video 3, Tape
MD/CDR, CD Aux
Press the corresponding button to change the input source. Pressing the
Tuner AM/FM button a second time toggles between FM and AM modes.
Please refer to the Operating Instructions section of this manual for more information on some functions of these buttons.


14 Azur AV receiver
The RV has several music and home-cinema listening modes available, all designed to reproduce surround sound effects,
dependant on the input signal and speaker setup:
Stereo
Only the Front Left and Front Right speakers (and subwoofer if selected)
have output in this mode. If an analog source is selected you will be listening to pure analog stereo with no digital signal processing. If a digital source is selected the RV will act as a digital to analog converter and playback stereo LPCM as output by CD players etc.
Dolby Digital (Provides (up to) 5.1 output from suitable encoded Dolby Digital material using 5 main speakers (Left Front , Right Front , Centre, Left Surround,
Right Surround) and a subwoofer. Decoding Dolby Digital requires a
Dolby Digital encoded DVD disc and a digital connection from the RV to the source equipment (Such as a DVD player).
DTS (5.1)
DTS also provides (up to) 5.1 output from suitable encoded DTS material using 5 main speakers (Left front , Right front , Centre, Left Surround,
Right Surround) and a subwoofer. Decoding DTS requires a suitably encoded DTS disc and a digital connection from the RV to the source equipment.
Dolby Digital EX (An enhanced form of Dolby Digital, DD EX provides an extra channel
(Surround Back) for greater image depth and more solid sound localisation behind the listener. DD EX requires a DD EX encoded disc.
DTS-ES Discrete (An enhanced form of DTS, ES provides an extra channel (Surround Back)
SURROUND SOUND MODES
for greater image depth and more solid sound localisation behind the listener. All channels are discretely encoded digitally for the best possible surround sound effect. DTS-ES Discrete requires a DTS-ES
Discrete encoded disc.
DTS-ES Matrix (Another enhanced form of DTS, ES Matrix also provides an extra channel
(Surround Back) but instead the extra channel is inserted into the left and right surround channels in a matrix process. DTS-ES Matrix requires a DTS-ES Matrix encoded disc.
Pro Logic II
A newer version of Dolby Pro Logic which is able to recreate 5.1 surround sound from suitable encoded analog source material. The source material is stereo (and can be played as such) but also has special encoding that allows the RV to decode a 5.1 surround sound output. There are 5 standard modes Movie, Music, Virtual, Pro Logic
Emulation and Matrix.
DTS Neo:6
A DTS technology which is able to recreate 6.1 surround sound from suitable encoded analog source material. The source material is stereo
(and can be played as such) but also has special encoding that allows the RV to decode a 6.1 surround sound output. There are standard modes Cinema and Music.
DSP modes
These modes allow a realistic surround-sound experience from source material that has no encoding at all. The surround sound effect is achieved by Digital Signal Processing of the Analog or Digital stereo source used. Five modes are possible Theater, Hall, Movie, Music and
Room.

RV AV receiver
Azur AV receiver The diagram shows atypical example of a 5.1/6.1 loudspeaker setup.
Always adjust the speaker and listening positions until you are happy with the sound. Please refer to the loudspeaker and subwoofer manuals for more detailed positioning information.
Front Left and Right speakers
-
For stereo and multi-channel sound.
Angle towards the listening position.
Centre speaker
-
For dialogue and centre sounds. Position at a similar height to the front left and right speakers (above or below the
TV/monitor). Using a centre speaker from the same manufacturer/range as used used for the front left and right speakers is advisable. This timbre matching allows surround effects to flow more naturally from left to right without obvious transitions between the speakers.
Surround Left and Right speakers
-
For ambient and multi-channel sound. Floorstanding speakers should be angled towards the listening position. Bookshelf/standmount speakers should be wall mounted or used with dedicated speaker stands, positioned at or above ear height.
To set the required delay between speakers for surround sound modes,
please refer to the Surround Sound Setup section of this manual.
Surround Back speaker Optional sixth channel speaker, required for enjoying Dolby
®
Digital EX or DTS
®
-ES audio. Improves the quality of sound effects by filling the gap between the surround left and rear right speakers. Position the speaker firing towards the front of the room.
Subwoofer - For improving the bass in your system, as well as reproducing LFE cinema effects when playing Dolby Digital or DTS
encoded discs. Your subwoofer can often be placed almost anywhere in the room as bass is less directional, but experimentation with positioning is recommended.
LOUDSPEAKER POSITIONING 2
3 5
4 5.1/6.1 1
1 2
4 3
3 5
*
* Optional “6th” speaker


16 Azur AV receiver
To avoid damaging the speakers with a sudden high-level signal, be sure to switch the power off before connecting the speakers. Check the impedance of your speakers. Speakers with an impedance of between and 8 ohms (each) are recommended. The coloured speaker terminals are positive (+) and the black speaker terminals are negative (-). Make sure correct polarity is maintained at each speaker connector or the sound can become weak and “phasey”
with little bass.
Prepare the speaker cords for connection by stripping off approximately
10mm (3/8”) or less (no more than mm, as this could cause a short- circuit) of the outer insulation. Twist the wire tightly together so there are no loose ends. Unscrew the speaker terminal knob, insert the speaker cable, tighten the knob and secure the cable.
Note: All connections are made via loudspeaker cable, except if using an active subwoofer which would be connected via a standard RCA phono cable. Banana Plugs (mm standard) connected to the speaker cable are recommended for direct insertion into the speaker terminals.
LOUDSPEAKER CONNECTIONS
Power Rating VAC 50Hz
Sur
Left
Sur
Right
Sur
Back
Left
Right
Centre
Reset
Power
On
Off
SB
SB
SW
SW
Cen
C
SR
R
SL
L
Power AC
Max Power Consumption Wt In Preamp Out
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Component Video In
DVD
Video Video Component Video Out www.cambridge-audio.com
Designed in London, England
Speaker Impedance 4-8 Ohms
Control
Bus
Serial No. label fitted on underside
In
Front right speaker Front left speaker Surround left speaker Surround right speaker Front centre speaker
Surround back speaker
Powered subwoofer
Phono/RCA cable

RV AV receiver
Azur AV receiver VIDEO CONNECTIONS
Power Rating VAC 50Hz
FM 75

AM
Loop
300

Video Video 1
DVD
Sur
Left
Sur
Right
Sur
Back
Left
Right
Centre
Reset
Power
On
Off
Tape Play
Tape Rec
CD
DVD
CD/Aux
Video Video 1
DVD
CD
Video Video 2
DVD
Video Video 1
DVD
SB
SB
SW
SW
Cen
C
SR
SR
R
R
SL
SL
L
L
Power AC
Max Power Consumption W Direct In Preamp Out
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Component Video In
DVD
Video Video 2
Tuner
RS232C
S-Video In
Optical In
Composite Video In
Audio In
Tape
L
R
L
R
Coax In
Coax In
Coax Out
Optical
Out
Component Video Out
Risk of electric shock
Do not open
Caution / Avis /Achtung
Risque de choc electrique
Ne pas ouvrir
Vorm öffnen des gërates
Netzstecker ziehen www.cambridge-audio.com
Designed in London, England
Speaker Impedance 4-8 Ohms
Video Video 2
Control
Bus
This device complies with part 15 of FCC rules
Manufactured in an ISO9002
approved facility
TV/Mon Out
S-Video
Com posit e
azur R V2.0
AV Receiver
Serial No. label fitted on underside
In
AUDIO CONNECTIONS
Power Rating VAC 50Hz
FM 75

AM
Loop
300

Video Video 1
DVD
Sur
Left
Sur
Right
Sur
Back
Left
Right
Centre
Reset
Power
On
Off
Tape Play
Tape Rec
CD
DVD
CD/Aux
Video Video 1
DVD
CD
Video Video 2
DVD
Video Video 1
DVD
SB
SB
SW
SW
Cen
C
SR
SR
R
R
SL
SL
L
L
Power AC
Max Power Consumption W Direct In Preamp Out
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Component Video In
DVD
Video Video 2
Tuner
RS232C
S-Video In
Optical In
Composite Video In
Audio In
Tape
L
R
L
R
Coax In
Coax In
Coax Out
Optical
Out
Component Video Out
Risk of electric shock
Do not open
Caution / Avis /Achtung
Risque de choc electrique
Ne pas ouvrir
Vorm öffnen des gërates
Netzstecker ziehen www.cambridge-audio.com
Designed in London, England
Speaker Impedance 4-8 Ohms
Video Video 2
Control
Bus
This device complies with part 15 of FCC rules
Manufactured in an ISO9002
approved facility
TV/Mon Out
S-Video
Com posit e
azur R V2.0
AV Receiver
Serial No. label fitted on underside
In
Note: Do not plugin the mains power lead or turn the unit on until all connections have been made.
Connect to source equipment using stereo phono cables (stereo 2RCA-
2RCA). Tape/MD/CDR recorder/players require two sets of stereo phono/RCA cables, one for recording, one for listening.
Three types of video connections can be made on the R V2.0:
Composite (1), S-Video (2) and Component (3). For best picture quality we recommend making Component video connections, then in declining order of quality, S-Video connections and then Composite video connections. The RV does not provide conversion between
Composite, S-Video or Component video formats (e.g. if you are watching a S-Video input from a DVD, you must view it from the S-Video output on the R V2.0).
CD player
DVD player
Tape player/recorder
Component cable
(3RCA-3RCA)
S-Video cable
Single 75 ohm
Phono cable
(RCA-RCA)
DVD player
TV/Monitor
Component cable
(3RCA-3RCA)
2 DVD player
TV/Monitor
DVD player
TV/Monitor
Phono cable (2RCA-2RCA)
Phono cable (2RCA-2RCA)


18 Azur AV receiver
DIGITAL CONNECTIONS
Power Rating VAC 50Hz
FM 75

AM
Loop
300

Video Video 1
DVD
Sur
Left
Sur
Right
Sur
Back
Left
Right
Centre
Reset
Power
On
Off
Tape Play
Tape Rec
CD
DVD
CD/Aux
Video Video 1
DVD
CD
Video Video 2
DVD
Video Video 1
DVD
SB
SB
SW
SW
Cen
C
SR
SR
R
R
SL
SL
L
L
Power AC
Max Power Consumption W Direct In Preamp Out
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Component Video In
DVD
Video Video 2
Tuner
RS232C
S-Video In
Optical In
Composite Video In
Audio In
Tape
L
R
L
R
Coax In
Coax In
Coax Out
Optical
Out
Component Video Out
Risk of electric shock
Do not open
Caution / Avis /Achtung
Risque de choc electrique
Ne pas ouvrir
Vorm öffnen des gërates
Netzstecker ziehen www.cambridge-audio.com
Designed in London, England
Speaker Impedance 4-8 Ohms
Video Video 2
Control
Bus
This device complies with part 15 of FCC rules
Manufactured in an ISO9002
approved facility
TV/Mon Out
S-Video
Com posit e
azur R V2.0
AV Receiver
Serial No. label fitted on underside
In
Two types of digital audio connections can be made to the R V2.0,
Optical/Toslink and Coaxial/SPDIF. Either type can be used for each source as the RV is able to convert between the two. Only one connection type should be used per source.
Whichever type is used to connect to the digital inputs, both the coaxial/SPDIF and optical/toslink outputs on the RV will be active.
Optical cable
(OPT-OPT)
DVD player
CD player
MD/DVD-R/CD-R
6.1 DIRECT IN
Power Rating VAC 50Hz
FM 75

AM
Loop
300

Video Video 1
DVD
Sur
Left
Sur
Right
Sur
Back
Left
Right
Centre
Reset
Power
On
Off
Tape Play
Tape Rec
CD
DVD
CD/Aux
Video Video 1
DVD
CD
Video Video 2
DVD
Video Video 1
DVD
SB
SB
SW
SW
Cen
C
SR
SR
R
R
SL
SL
L
L
Power AC
Max Power Consumption W Direct In Preamp Out
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Component Video In
DVD
Video Video 2
Tuner
RS232C
S-Video In
Optical In
Composite Video In
Audio In
Tape
L
R
L
R
Coax In
Coax In
Coax Out
Optical
Out
Component Video Out
Risk of electric shock
Do not open
Caution / Avis /Achtung
Risque de choc electrique
Ne pas ouvrir
Vorm öffnen des gërates
Netzstecker ziehen www.cambridge-audio.com
Designed in London, England
Speaker Impedance 4-8 Ohms
Video Video 2
Control
Bus
This device complies with part 15 of FCC rules
Manufactured in an ISO9002
approved facility
TV/Mon Out
S-Video
Com posit e
azur R V2.0
AV Receiver
Serial No. label fitted on underside
In
To listen to multi-channel DVD Audio player or SACD discs connect your
DVD/SACD player to the 6.1 Direct In sockets. As any signals connected to the 6.1 Direct Input (multi-channel DVD-A /
SACD etc) will have been decoded by an external unit it maybe necessary to adjust the relative levels of each channel when listening to this input.
This can be done using the CH Select button on the remote, the RVs front panel display will rotate round each channel in turn. Use Volume up/down on the remote to adjust the relative level of each input channel in turn by -dB to +dB in dB steps. If no adjustment is made for 5 seconds the unit saves the settings and returns to its normal state. Note that any changes made are saved and will affect all surround sound modes.
DVD-A player or SACD multi-channel player 5.1 or 6.1 connections
OR
OR
OR
OR
Phono cable (2RCA-2RCA)

RV AV receiver
Azur AV receiver Power Rating VAC 50Hz
FM 75

AM
Loop
300

Video Video 1
DVD
Sur
Left
Sur
Right
Sur
Back
Left
Right
Centre
Reset
Power
On
Off
Tape Play
Tape Rec
CD
DVD
CD/Aux
Video Video 1
DVD
CD
Video Video 2
DVD
Video Video 1
DVD
SB
SB
SW
SW
Cen
C
SR
SR
R
R
SL
SL
L
L
Power AC
Max Power Consumption W Direct In Preamp Out
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
Component Video In
DVD
Video Video 2
Tuner
RS232C
S-Video In
Optical In
Composite Video In
Audio In
Tape
L
R
L
R
Coax In
Coax In
Coax Out
Optical
Out
Component Video Out
Risk of electric shock
Do not open
Caution / Avis /Achtung
Risque de choc electrique
Ne pas ouvrir
Vorm öffnen des gërates
Netzstecker ziehen www.cambridge-audio.com
Designed in London, England
Speaker Impedance 4-8 Ohms
Video Video 2
Control
Bus
This device complies with part 15 of FCC rules
Manufactured in an ISO9002
approved facility
TV/Mon Out
S-Video
Com posit e
azur R V2.0
AV Receiver
Serial No. label fitted on underside
In
Power amplifier PREAMP OUT
To connect external power amplifiers, use Phono/RCA leads connected to the 6.1 Preamp Outputs on the rear panel. Set the Pre Out setting in the Output Setup OSD menu to 'Pre Out' rather than 'Normal. This mutes the internal power amplifiers as they are not being used.
Phono cable (2RCA-2RCA)
FRONT INPUT CONNECTIONS
Volume
DVD
Video Dolby Digital EX/
DTS ES
DSP
Mode
Pro Logic II/
Neo Input
Mode
Video 3 inputs
Video
Left
Right
Stereo
Video Video Tuner FM/AM Tape/MD/CDR
CD/Aux
6.1 Direct azur
540R
AV Receiver
Video games console
(or video camera recorder)
The front panel Video 3 input is for temporary connections to video games consoles etc. Remove the cap to access the Video 3 inputs, and connect to a video game or video camera’s outputs using a composite video cable and stereo phono cable (RCA-RCA).
Composite video cable
Stereo phono cable
(RCA-RCA)


20 Azur AV receiver
FM aerial
Connect an aerial to the FM 75 ohm socket (a simple wire aerial is supplied for temporary use. Extend the lead and move the aerial around until you get the best reception. For continued use, we strongly recommended using a 75 ohm outdoor FM aerial.
AM loop aerial
Connect each end of the single length antenna to the antenna terminals. Place the antenna as far from the main system as possible to prevent unwanted noise and to obtain optimum reception. If the AM loop aerial provided does not receive sufficient reception, it maybe necessary to use an outdoor AM aerial.
AERIAL CONNECTIONS
FM 75

AM
Loop
300

Video Video 1
CD/Aux
Video Video Video Video 1
Tuner
RS232C
S-Video In
Composite Video Audio In
L
R
Risk of electric shock
Do not open
Caution / Avis /Achtung
Risque de choc electrique
Ne pas ouvrir
Vorm öffnen des gërates
Netzstecker ziehen
This device complies with part 15 of FCC rules
Manufactured in an ISO9002
approved facility
TV/Mon Out
S-Video
Com posit e
azur R V2.0
AV Receiver
FM aerial
FM external aerial
AM external aerial
AM loop aerial
OR
OR
Ground
ON-SCREEN DISPLAY (OSD)
Once the RV is connected to all AV components, the system setup can be completed either using the display on the front of the unit,
or if connected to a screen/monitor, via an onscreen display setup menu (recommended. To access this menu, press the On-screen



Share with your friends:
  1   2   3   4


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
yamaha