An introduction to the



Download 195.58 Kb.
View original pdf
Page1/2
Date06.12.2018
Size195.58 Kb.
  1   2

an introduction to the
WQXGA projector user’s guide www.projectiondesign.com an introduction to the
WQXGA projector
F35 user’s guide
Designed and manufactured in Fredrikstad, Norway.

english
2
F35 User’s Guide – Introduction
This page intentionally left blank.

www.projectiondesign.com english
3
Contents of this User’s Guide
1 Introduction
5 1.1 Thank you
1.2 Features
2 SAFETY
7 2.1 SAFETY
2.2 WARNING
2.2.1
INFORMATION AND WARNING ABOUT POTENTIAL HEALTH ISSUES RELATED TO MERCURY
VAPOR (This section only applies to projectors with UHP lamps)
2.3 WEEE INFORMATION
2.4 WARNING
2.4.1
SERVICE PERSONNEL INFORMATION WARNING
2.4.2
REMOTE CONTROL WARNING
2.4.3
WARNING SYMBOLS
2.5 FCC
2.6 SERVICE INFORMATION
3
Getting to know the projector
11 3.1 Overview
3.2 Indicators
3.2.1
The status indicator
3.2.2 Keypad
3.2.3
Remote control
3.2.4 Connectivity
3.2.5
Graphical User Interface (GUI)
4
What’s in the box?
17 5
Basic setup
19 5.1 Lens
5.1.1
Lens and lens mount
5.1.2
Inserting a lens
5.1.3
Replacing a lens
5.2 Adjusting on screen image size and position
5.3 Lamp operation
5.4 Ceiling mount
5.4.1
Ceiling mount cover
5.4.2
Attaching the ceiling cover
5.5 Connecting and cables
5.5.1
Setting up a video source
5.5.2
Setting up a computer source
5.5.3
Connecting command and control interfaces


User’s Guide – Introduction
F35 User’s Guide – Introduction english
4 5.6 Image alignment
5.7 Setting image orientation
5.8 Using source scan
5.9 Limiting OSD messages
5.10 Using the dual lamp system
5.11 Changing the language of the menu system
5.12 Identifying system status
5.12.1
Getting information about the active source
6
Advanced setup
27 6.1 Controlling multiple projectors with remote control ID (RCID)
6.2 Protecting the projector with a pin code
6.3 Using dual head input
6.4 Setting custom color space and digital level
6.5 Disabling IR receivers
6.6 Controlling screens with triggers
6.7 Setting aspect trigger behavior
6.8 Automatic power on/off
6.8.1
Using the timer
6.8.2
Using DPMS (Display Power Management Signaling)
6.9 Disabling LED indicators
6.10 Setting the background color
6.11 Setting OSD menu timeout
6.12 Selecting the startup logo
7
Optimising the picture
31 7.1 Calibration data
7.1.1
Updating RealColor™ calibration data
7.2
Working with RealColor™
7.2.1
Setting the BrilliantColor™ correctly
7.2.2 Gamma
7.2.3
RealColor™ operating modes
7.2.4
Setting a white point or color temperature
7.2.5
Defining the system color gamut
8
Technical specifications
37 8.1 Product details
9 Maintenance
39 9.1 Software upgrades
9.2 Lamp replacement

www.projectiondesign.com english
5 1 Introduction
1.1 Thank you
Thank you for purchasing a F35 projector.
The F35 WQXGA resolution projector sets an industry benchmark for projectors in its size and performance category. Featuring high resolution DLP technology, high performance optics and lenses, updated signal processing and built-in frame-lock synchronisation makes the F35 the ideal projector for multi-channel visualisation and simulation applications, where realism and reliability are key criteria.
1.2 Features
• WQXGA (2560 x 1600) resolution single chip DLP® technology
• Patented Dual Architecture or LED illumination system and optics
• RealColor advanced colour management suite
• Fail safe, hot swap Dual Lamp architecture or longlife LED illumination
• Dual optomechanical IRIS for customizable brightness and contrast
• Full powered horizontal and vertical lens shift, allows direct stacking
• Full 12-bit colour resolution for minimised artefacting and high accuracy
• BrilliantColor™ technology with six-colour processing for accurate colours
• Elevated contrast levels for unmatched image dynamics
• High brightness for large screen applications
• Range of application specific colour wheel options
• Wide range of projection lenses
• Highly versatile colour management and calibration options
• Built-in real time clock for timed operations
• Sigma Designs™ technology video de-interlacing and processing
• Economy mode for reduced power consumption and prolonged lamp life
• Small and ergonomic footprint, with low weight
• Direct view status monitor and lamp function indicators
• Multiple video and graphics inputs for virtually any video and data source
• Dual Link DVI (330 MHz)
• HDMI ver. 1.3a
• LAN, RS232 and USB ports for control and monitoring


User’s Guide – Introduction
F35 User’s Guide – Introduction english
6

english
7
www.projectiondesign.com
2 SAFETY
This device complies with safety regulations for Information Technology Equipment intended to operate in “normal” environments (offices and homes). Before using the device for the first time, please read the safety instructions thoroughly.
2.1 SAFETY
This user guide contains important information about safety precautions and the set-up and use of the projector. Please read the manual carefully before you operate the projector.
This device complies with relevant safety regulations for data processing equipment for use in an office environment. Before using the projector for the first time, please read the safety instructions thoroughly.
2.2 WARNING
Use only the cables and cords supplied with the projector or original replacement cables. Us- ing other cables or cords may lead to malfunction and permanent damage of the unit.
Always use 3-prong / grounded power cord to ensure proper grounding of the unit. Never use 2-prong power cords, as this is dangerous and could lead to electrical shock.
Never open the unit. The projector contains no user serviceable parts. Refer all repairs to qualified personnel only. Make sure that no objects enter into the vents and openings of the set.
Do not spill any liquids on the projector or into the vents or openings of the unit.
Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due to the high energy light emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens.
Do not look into the projection lens when the projector is switched on. The strong light may permanently damage sight. Do not look into the laser beam when activated on the remote control. Laser light may permanently damage sight.
Do not point laser beam at people or animals.
Only place the projector on a stable surface, or mount it securely using an approved ceiling- mount.
Do not drop the projector.
Always operate the projector according to the rotation guidelines found on the web. Operat- ing the unit in other positions may reduce lamp life significantly, and may lead to overheating, resulting in malfunctioning.
Always allow ample airflow through the projector. Never block any of the air vents. Never cover the unit in any way while running. Allow for sufficient distance to walls and ceilings to avoid overheating.
Minimum safety distance to any side of the unit is 50 cm / 20” in any direction.
CAUTION! Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than 50cm / 20” to the exhaust vent.
The projector is designed for indoor use only. Never operate the unit outdoors.
Do not operate the projector outside its temperature and humidity specifications, as this may result in overheating and malfunctioning.

english
8
User’s Guide - SAFETY
F35 user’s guide - SAFETY
CAUTION! Connecting sources to a powered projector may result in product failure. It is recommended that the power cable connector (projector-end) or the mains power socket are accessible whilst the product is in use to enable mains power to be disconnected or switched off when connecting source devices. This should be considered during product installation.
Only connect the projector to signal sources and voltages as described in the technical specification. Connecting to unspecified signal sources or voltages may lead to malfunction and permanent damage of the unit.
Allow lamp to cool down before changing. One lamp may be changed while the other lamp is operating (hot-swap).
2.2.1 INFORMATION AND WARNING ABOUT POTENTIAL HEALTH ISSUES RELATED
TO MERCURY VAPOR
(This section only applies to projectors with UHP lamps)
This projector uses a very powerful UHP™ lamp for illumination to produce an extremely bright image.
This technology is similar to other high-pressure discharge lamps that are extensively used in cars, street lights and other lighting appliances today. These lamps, like fluorescent lighting, contain small amounts of mercury. The amount of mercury present in a lamp is far below the limits of danger set by the authorities. It is very important that lamps containing mercury are treated properly to minimize potential health hazards.
The UHP™ lamp, like any other high brightness projector lamp, is under high-pressure when operating. While the lamp and the projector are carefully designed to minimize the prob- ability of lamp rupture, the lamp may break while operating and small amounts of mercury vapor may be emitted from the projector. The probability of rupture increases when the lamp reaches its nominal life. It is therefore highly recommended that the lamp is replaced when the rated lifetime is reached.
As a general precaution, secure good ventilation in the room when operating the projector. If lamp rupture occurs, evacuate the room and secure good ventilation. Children and pregnant women in particular should leave the room.
When replacing a worn lamp, dispose of the used lamp carefully by proper recycling.
Mercury is a naturally occurring, stable metallic element that may pose a safety risk to people under certain conditions. According to the Public Health Statement for Mercury published by the Agency for Toxic Substances and Disease Registry (“ATSDR”, part of the United States
Public Health Service), the brain, central nervous system and kidneys are sensitive to the effects of mercury, and permanent damage can occur at sufficiently high levels of exposure.
Acute exposure to high concentrations of mercury vapor can cause conditions such as lung and airway irritation, tightness in the chest, a burning sensation in the lungs, coughing, nausea, vomiting and diarrhea. Children and fetuses are particularly sensitive to the harmful effects of metallic mercury to the nervous system.
Seek medical attention if any of the above symptoms are experienced or if other unusual conditions are experienced following lamp rupture.
2.3 WEEE INFORMATION
This product conforms to all requirements of the EU Directive on waste electrical and elec- tronic equipment (WEEE). This product shall be recycled properly. It can be disassembled to facilitate proper recycling of it’s individual parts. This product is using projection lamps that shall be recycled properly. Consult your dealer or relevant public authority regarding drop-off points for collection of WEEE.

english
9
www.projectiondesign.com
2.4 WARNING
This product contains chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Recycle properly, do not dispose of in ordinary waste!
2.4.1 SERVICE PERSONNEL INFORMATION WARNING
Use UV radiation eyes and skin protection during serviceing.
2.4.2 REMOTE CONTROL WARNING
Laser radiation class II product; wavelength 670nm; maximum output 1mW.
Remote control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable requirements of EN/IEC 60825-1/2007 2.4.3 WARNING SYMBOLS
READ USER GUIDE Attention! Read the user guide for further information!
DANGEROUS VOLTAGE Danger! High voltage inside the product!
HOT Warning! Hot surfaces!
WAIT Warning! Wait until cooled down!
MERCURY Warning! Lamp contains mercury! Recycle properly, do not dispose of in ordinary waste!
UV Warning! UV radiation inside the product!
RECYCLE Warning! Recycle properly, do not dispose of in ordinary waste!
NO TELEPHONE Warning! Do not connect to telephone lines!
2.5 FCC
FCC regulations provide that changes or modifications not expressly approved by the party responsible manufacturer could void your authority to operate the equipment.
NOTE! This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio fre- quency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CANADA
This Class A digital apparatus complies with Canadian ICES-003. / Cet appareil numérique de la classe A est conforme à la norme NMB- 003 du Canada.
WARNING!
This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

english
10
User’s Guide - SAFETY
F35 user’s guide - SAFETY
2.6 SERVICE INFORMATION
This product contains no user serviceable parts. If the product fails to function as expected, please first check that all connections are properly made, and that the power cord is properly connected. Please check that the projector as well as the video and computer sources are all switched on. Cables and cords may break over time. Try to change cables and cords, in case there is a bad or intermittent connection. Check if the circuit breaker or fuse of your mains is intact. In the event of product failure, please contact your reseller. You should prepare a description of the symptoms of failure you experience. Please also state product number and serial number as printed on the label on the bottom of the projector.

english
11
www.projectiondesign.com
3 Getting to know the projector
3.1 Overview
A Lens
B IR sensor
C Ventilation
D Lens release
E Power connector
F Keypad
G Connector panel
H LCD
I Lamp lids
J Adjustable feet
K Security lock
L Ceiling mount
Figure 3-1. - Projector front view
Figure 3-2. - Projector rear view
Figure 3-3. - Projector bottom view
A
B
C
D
B
C
C
E
H
B
G
C
B
I
F
J
J
K
B
L

english
12
User’s Guide – Getting to know the projector
F35 User’s Guide – Getting to know the projector
3.2 Indicators
System status indicators are located right of the keypad on the back of the projector. Figure
3-4 shows the three status indicators – one for each lamp and one for the system status.
Figure 3-4. The lamp indicators
For the lamp indicators the following apply:
- PERMANENT GREEN LIGHT: The lamp is on and operating normally.
- PERMANENT YELLOW LIGHT: The lamp is off. The lamp may be disabled in the menu or the system is in standby.
- PERMANENT RED LIGHT: Lamp life has expired, lamp is not igniting or lamp door is open. If the lamp life has expired, please change projection lamp immediately. Failing to change lamp may lead to lamp explosion. Please replace with original projectiondesign equipment.
- FLASHING YELLOW LIGHT: The lamp is cooling down. The total cooling down time is approx. 45 seconds.
- NO LIGHT: No lamp inserted.
NOTE! The replacement lamps must be purchased from an authorized projectiondesign dealer for the warranty of the product to be valid.
3.2.1 The status indicator
- PERMANENT GREEN LIGHT: The projector is turned on and in normal operation.
- PERMANENT YELLOW LIGHT: The projector is in standby mode. If the projector was powered off by the power saving feature (DPMS), it will automatically power on when you connect a valid source.
- FLASHING YELLOW LIGHT: Please wait. The yellow light will flash a period after power cord is connected (20-30 sec.), and a period after going to standby mode while lamp is cooling down (approximately 45 sec.). The projector may not be turned on again until the light has turned to permanent yellow.
- FLASHING RED LIGHT: Projector is overheated. Turn off immediately! Check if air inlets are covered or if ambient temperature is outside specifications. The projector cannot be restarted until the power cord is disconnected and reconnected again. If the projector continues to flash red, you will need to return the unit for service.

english
13
www.projectiondesign.com
3.2.2 Keypad
The projector has an illuminated keypad on the back of the unit. Figure 3-5 shows the keypad.
Figure 3-5. Projector keypad
The keypad is used to:
- navigate the menu system
- scroll the information in the LCD panel
- directly select input sources
- enter pin code (if enabled)
- power on/off
- adjust basic image functions
The keypad is illuminated for operation in dark environments. Available functions are illuminated in yellow while selected (active) functions are illuminated in green. Functions that are not available are not illuminated.
3.2.3 Remote control
The remote control allows flexible access to the projector settings, either through direct keys, or through the menu system. The remote control is backlit for use in dark environments.
It also has a data-jack that allows for wired connection to the projector. When the wire is connected, the IR (infra-red) beam and internal batteries are switched off.
Note! The direct sources buttons for VGA1, VGA2, X-Port 2 and YPbPr are not available for all versions of the product. If your product does not have these inputs implemented the OSD will display “not available” when pressing these buttons.
Figure 3-6. Remote control

english
14
User’s Guide – Getting to know the projector
F35 User’s Guide – Getting to know the projector
3.2.4 Connectivity
The projector features a wide range of video inputs and command/control connectors.
Figure 3-7 shows the connector panel.
Figure 3-7. Connector panel
A LAN: 10/100 Mbit Ethernet connector for command, control and software upgrade.
B RC INPUT: 3.5mm mini-jack connector. Allows connection of external IR receiver or wired remote control.
C TRIGGERS: 3.5mm mini-jack connector triggers. Used for controlling peripheral equipment like motorized screens.
D 3D SYNC: Reserved for future use.
E RS-232: Allows for wired remote control and monitoring of many projector functions used in installation environments.
F
USB-A: Allows for software upgrades using a standard USB memory stick.
G USB-B: Reserved for future use.
H SYNC-IN: Allows for taking an external vertical sync signal and using that with the select video input. This is mainly used in multiple projector installations with requirement of video synchronization between the units.
I
SYNC-OUT: Constantly outputs the vertical sync signal of the active video input. This is mainly used in multiple projector installations with requirement of synchronization between the units.
J
DVI-D: Two Dual Link DVI-D connectors with bandwidth up to 330 Mhz total. These connectors can also be used to form one uniform image by feeding half of the image into each connector. HDCP compliant for sources up 165 Mhz.
K HDMI 1.3: Two HDMI 1.3a connectors with bandwidth up to 165 Mhz each. These connectors can also be used to form one uniform image by feeding half of the image into each connector. HDCP compliant. All video formats specified by the HDMI 1.3a are supported.
A
C
B
D
E
F
G
H
I
J
K

english
15
www.projectiondesign.com
3.2.5 Graphical User Interface (GUI)
The projector has an easy-to-use on screen display (OSD) system for controlling the extensive number of features implemented. “Figure 3-8. Top level OSD menu”, shows the top level of the OSD menu.
Figure 3-8. Top level OSD menu
Activate the menu by pressing the “MENU” button on either the keypad or the remote control. Navigate the menu using the arrow keys.
The various functions in OSD menu is described in Chapter “5 Basic setup”.
picture installation settings language status

english
16
User’s Guide – Getting to know the projector
F35 User’s Guide – Getting to know the projector

english
17
www.projectiondesign.com
4 What’s in the box?
The projector comes with the following components:
Projector
Power Cable (Country Dependant)
Remote Control
HDMI-cable
DVI-cable
Ceiling mount Cable Cover
User Documentation
Please verify that you have all compoents upon unpacking the unit, and its contents.
Please save packaging materials for future use, should it be necessary to ship the unit.

english
18
User’s Guide - What’s in the Box?
F35 User’s Guide - What’s in the Box?

english
19
www.projectiondesign.com
5 Basic setup
5.1 Lens
5.1.1 Lens and lens mount
A range of fixed and zoom lenses is available to cover most applications, both front and rear.
The lenses are powered and fitted with a bayonet mount for ease of installation.
IMPORTANT! Switch off all equipment before setting-up for proper function.
When mounting and changing lenses, be aware that the optical system is exposed to dust and foreign particles as long as the lens is not attached to the system. Do not leave the lens mount open longer than necessary to change lens. If a lens is not mounted, always insert the protection lid to avoid dust and foreign particles entering the internal optics.
IMPORTANT! Never run the projector without lens mounted.
5.1.2 Inserting a lens
To insert a lens please follow this procedure:
A Remove the protection lid from the bayonet mount by turning the knob anti-clockwise.
B Remove the rear lens cap.
C Attach the projection lens using the bayonet mount, observing the red insertion marks.
D Turn the lens firmly clockwise until it stops with a click.
E Remove the lens cap from the projection lens. If you switch the projector on with the lens cap in place, the lens cap may melt, damaging not only the lens cap, but also the projection lens and surrounding parts.
5.1.3 Replacing a lens
To replace a lens please follow this procedure:
A To change lens, first remove the current lens by pushing the release button and twisting the lens counter-clockwise until it comes loose. Pull the lens out.
B Insert the new lens as described in above.
A
B
C
D
E
F

english
20
User’s Guide - Basic setup
F35 User’s Guide - Basic setup
5.2 Adjusting on screen image size and position
Adjusting the placement of the image on screen can be done using the:
1. Adjustable feet (E in Figure 5-1).
2. Lens shift mechanism controlled from the keypad, the remote control, RS-232 or LAN (A in Figure 9).
3. Zoom (for lenses with zoom) in the lens controlled from the keypad, the remote control,
RS-232 or LAN (B in Figure 5-1).
After the correct image size and position is found, please adjust the image focus using the keypad, the remote control, RS-232 or LAN. (C in Figure 5-1).
Figure 5-1. Image size ans position adjustment
B
A
E
C

english
21
www.projectiondesign.com
5.3 Lamp operation
The projector is fitted with two individual projection lamps that can be run in various modes.
In addition, lamps can be replaced as needed separately. This ensures an optimized cost of ownership. Individual lamp timers are maintained for each lamp.
Lamp operation mode is controlled in the INSTALLATION > LAMPS sub menu.
5.4 Ceiling mount
The projector can be ceiling mounted using an approved UL tested/ listed ceiling mount fixture, with a capacity of minimum 60 kg / 130 lbs. For ceiling mount use M6 screws that penetrate maximum 15 mm / 0.6” into the projector body. “Figure 5-2. Ceiling mount”, gives detailed information about the alignment of the ceiling mount screw holes in the projector.
IMPORTANT! For proper ventilation the minimum distance from ceiling/ rear wall should be: 30/ 50 cm, 12/ 20 inch.
Figure 5-2. Ceiling mount
300mm
500mm
Ceiling Mount Interface
M6 Threads
384,9 111,8 94,3 15,5 95 82,5 59,5 53 510 123,1 163,3 233 300mm
500mm
Ceiling Mount Inter face
M6 Threads
384,9 111,8 94,3 15,5 95 82,5 59,5 53 510 123,1 163,3 233 300mm
500mm
Ceiling Mount Interface
M6 Threads
384,9 111,8 94,3 15,5 95 82,5 59,5 53 510 123,1 163,3 233

english
22
User’s Guide - Basic setup
A
B
C
F35 User’s Guide - Basic setup
5.4.1 Ceiling mount cover
The supplied auxiliary cable cover can be mounted on the projector to conceal the interface cables and power cord when the unit is ceiling mounted. Connect all cables and fix them in place before the cable cover is attached to the projector. Figure 5-3 shows the ceiling mount cover.
Figure 5-3. The ceiling mount cover
5.4.2 Attaching the ceiling cover
To attach the ceiling mount cover, please follow this procedure:
A Attach the cable cover to the projector by inserting the horizontal hooks on the cover in the horizontal slots on the rear of the projector.
B Turn the cover until the vertical hooks on the cover are inserted into the vertical slots on the rear of the projector.
C The cover will snap in place, to release pull the vertical hooks on the cover out of the slots, letting the cover hinge on the horizontal hooks.

english
23
www.projectiondesign.com
5.5 Connecting and cables
NOTE! Before setting up, switch off all equipment and disconnect the power cord.
5.5.1
Setting up a video source
For best quality video, connect a digital video source using the HDMI 1.3a interface (A) in Fig- ure 5-4. Both HDMI inputs are HDCP copy protection compliant. Depending on cable quality, the projector is supporting the use of cables with lengths up 20 meters (65 feet).
Figure 5-4. Connecting a video source
5.5.2
Setting up a computer source
The projector may be connected to up to four computer sources simultaneously, using the
HDMI (A) and/or DVI-D (B) interfaces, shown in Figure 5-5. These interfaces are all-digital and will yield a projected image with very low noise.
Both DVI and HDMI are HDCP compliant with sources up to 1920x1200@60Hz (single link source up to 165 Mhz).
Figure 5-5. Connecting a computer source
NOTE! HDCP is not supported on higher resolution sources like 2560x1600@60Hz
(WQXGA).
Connect the power cord after the DVI cable is inserted properly.
5.5.3
Connecting command and control interfaces
The projector is supporting RS-232 and LAN command and control interfaces. Use the ASCII based, simple instruction set (SIS) protocol to communicate with the projector. A detailed description of the ASCII protocol is available for download at www.projectiondesign.com.
Connect the power cord after the selected command and control cables are inserted properly.
A
B
A

english
24
User’s Guide - Basic setup
F35 User’s Guide - Basic setup
5.6 Image alignment
For easier alignment of the projector, test images are built into the system.
To enable test images, go to the menu entry INSTALLATION > TEST IMAGE. Cycle the vari- ous test images using the arrow keys. When a test image matching the aspect ratio of your screen has been found, use the zoom, focus, lens shift and physical projector alignment to match the screen.
5.7 Setting image orientation
In relation to the screen, the projector supports the following installation orientations:
1. Desktop front (default)
2. Ceiling front
3. Desktop rear
4. Ceiling rear
To set the image orientation go to menu entry INSTALLATION > IMAGE ORIENTATION
5.8 Using source scan
The projector can automatically scan through all the input connectors for a valid signal. If a valid signal is found, the image will set up. This is called source scan.
Source scan is default disabled. When disabled, the projector will only search the selected in- put connector for a valid signal. Use the keypad, remote control or any command and control interface to change in selected input interface.
To set the source scan setting, go to menu entry INSTALLATION > SOURCE SCAN
5.9 Limiting OSD messages
When detecting sources and using the various features of the projector, OSD messages will appear on the screen. Which messages that are appearing can be partially controlled by the user. The OSD can run in these modes:
• ON. All messages, warning and information OSDs are displayed.
• OFF. No messages are shown.
• Only warnings. Only critical warning messages like temperature overheating will be shown.
Go to menu entry INSTALLATION > OSD ENABLE to control the OSD behavior
5.10 Using the dual lamp system
The projector is fitted with two individual projection lamps that can be run in various modes.
In addition, lamps can be replaced as needed separately. Individual lamp timers are main- tained for each lamp.
The lamps can be used in the following modes:
• Both lamps on. (Default)
• Single lamp 1. Just the lamp in lamp chamber 1 is on.
• Single lamp 2. Just the lamp in lamp chamber 2 is on.
• Auto switch. Each single lamp is on for a defined number of hours, before swapping automatically. The delay between the lamp swapping is user adjustable.
To set the lamp mode, go the menu entry INSTALLATION > LAMP > LAMP MODE
Each of the lamps can also be run in ECO mode or dimmed.
Go to menu entry INSTALLATION > LAMP for the options.

english
25
www.projectiondesign.com
5.11 Changing the language of the menu system
The projector menu system has a total of 11 user-selectable languages embedded for easier use all over the world. The default language is English.
The available languages are:
• English
• French
• German
• Spanish
• Russian
• Norwegian
• Swedish
• Korean
• Japanese
• Chinese Simplified
• Chinese Traditional
• Portuguese
• Italian
To change the language of the menu system, just select “LANGUAGE” from the top menu and select your desired language.
5.12 Identifying system status
For ease of use, the projector has a complete menu available for system status. It is easily accessible from the top menu. From this menu the following information can be read:
• Part number
• Serial number
• The year/week the projector was manufactured
• Current software version
• Runtime and remaining time for both lamps
• Total number of operating hours
• All network information
• Current lens mounted
Currently active source
5.12.1
Getting information about the active source
By selecting STATUS > SOURCE INFORMATION basic information about currently active source is displayed.
If a deeper analysis is required for the currently active source, select STATUS > SOURCE IN-
FORMATION > ADVANCED. This menu provides detailed timing information for the currently active source.

english
26
User’s Guide - Basic setup
F35 User’s Guide - Basic setup

english
27
www.projectiondesign.com
6 Advanced setup
6.1 Controlling multiple projectors with remote control ID (RCID)
The remote control can be operated either in ‘broadcast mode’, or ‘individual mode’. When several projectors are in use in an installation, individual control may be convenient. Individual control is available either by wired remote control, using the data-jack, or by using an individ- ual number code. For individual control, first set the individual RC ID code using the projector menu system, see the SETTINGS sub menu. Then, to select a specific projector to control, first press the ‘*’ button in the lower keypad area, then the code as set in the target projector.
A code can be in the range ‘0’..’99’. ‘0’ is reserved for broadcast. To select another target, repeat the process by pressing ‘*’ and a new code. To exit individual control, press ‘*’’*’ twice or press ‘*’ and ‘0’.
6.2 Protecting the projector with a pin code
The projector may be controlled by a PIN (Personal Identification Number) code. The PIN code is 4 digits, and if the PIN code is activated, you must enter the correct code to unlock the projector. Factory set PIN (1234).
To activate, deactivate or change the PIN code, see the SETTINGS > PIN CODE sub menu.
NOTE! If an incorrect PIN code is entered, you may try again two times.
If you fail three times in a row, a PUK (unlock) code is needed. The PUK code is supplied with the product.
WARNING! Entering the puk code correctly is the customers responsibility
If you also fail three times with the PUK code, the projector locks up permanently, and can only be unlocked by a special service unlock code.
To access this code, you will need to contact your dealer or a service station. The service unlock code will be generated based on a secure, encrypted number that is produced by the projector itself. The projector will produce a new number every time.
NOTE! To unlock the projector, proof of ownership must be provided by the customer

english
28
User’s Guide - Advanced setup
F35 User’s Guide - Advanced setup
6.3 Using dual head input
For extended flexibility to connect high resolution sources with a pixel clock over 165 MHz, the projector is supporting a dual head input mode. In this mode the left and right half of the image can be connected to the DVI 1/DVI 2 or HDMI 1/HDMI 2 interfaces respectively
(Figure 6-1).
To enable this mode, go to the menu INSTALLATION > DUAL HEAD SETUP. Side-by-side is the only available option at this time.
Figure 6-1. Dual input mode
An example of this is feeding a WQXGA (2560x1600) source with 1280x1600 resolutions on each the DVI interfaces.
When enabling this mode, the EDID data on each of the DVI connectors will automatically be changed from WQXGA (2560x1600) to 1280x1600.
NOTE! For the image to be displayed in this mode, the resolution must be exactly the same on both connectors.
NOTE! In this mode the two connected sources must have exactly the same timing. A drift in timing between the inputs will result in a visible split in the center of image.
NOTE! Some graphic cards have problems with detecting the change from single head to dual head mode. If problems occur, disconnect both signal cables before enabling or disabling the dual mode in the menu.
6.4 Setting custom color space and digital level
The projector will automatically try to set the correct color space and digital drive level based on information from the source.
To manually override the automatically detected color space and digital level go to menu entry PICTURE -> ADVANCED. Set the “digital color space and level” to manual and select your color space and digital drive level.
6.5 Disabling IR receivers
The projector has 3 IR receivers as shown in chapter “3.1 Overview”.
These receivers can be individually disabled if necessary. Go to menu entry INSTALLATION >
IR FRONT / IR REAR LEFT / IR REAR RIGHT to disable the receivers.
1 2

english
29
www.projectiondesign.com
6.6 Controlling screens with triggers
The projector has to programmable triggers with 3.5 mm2 mini-jack connectors. These can be used to enable or disable screens, curtains or other peripheral equipment.
To change trigger settings, go to menu entry INSTALLATION > TRIGGER
By default:
• Trigger 1 is set to control a screen depending on whether projector is powered on or not.
• Trigger 2 is set to control a screen depending on the aspect ratio of currently active source.
Both triggers can be manually overridden both in the menu system and by using the com- mand and control protocol through RS-232 or LAN.
6.7 Setting aspect trigger behavior
To customize the aspect trigger functionality, go to menu entry INSTALLATION > TRIGGER >
ASPECT TRIGGER BEHAVIOR. In this sub-menu it is selectable for which input aspect ratios the trigger will be enabled.
6.8 Automatic power on/off
The projector can be automatically powered on or off by using the internal timer function or
DPMS.
6.8.1
Using the timer
The projector features a real-time clock that enables timing control. This means that the projector can be programmed to switch on and off at certain pre-set times during a weekly cycle.
To allow for a flexible schedule, 10 ‘programs’ are available. With each program, you can define the switch on or switch off time for a single day (Monday to Sunday), all work days
(Monday through Friday), or week-end (Saturday and Sunday). One, several or all programs can be active at the same time as desired. In this way, a flexible scheme can be established.
Observe the 24 hour time format. For more information, see the SETTINGS > TIMER menu.
The following example illustrates a case where the projector turns on at 08:00 in the morning
(8 am) and switches off at 20:00 (8 pm) on weekdays (Monday through Friday). Weekends
(Saturdays and Sundays), it turns on at 10:00 (10 am) and off at 18:00 (6 pm). VGA is used as the source. For this, four programs are needed, 2 for on and two for off.
6.8.2
Using DPMS (Display Power Management Signaling)
The projector is enabled for DPMS (Display Power Management Signaling). When enabled, the projector will automatically switch to standby mode after a specified time if there is no valid source present at its inputs. When a valid source is reconnected, the projector will start up again.
To enable or disable DPMS, go to menu entry SETTINGS > DPMS. The desired DPMS time- out is set in the DPMS > DPMS TIMEOUT menu entry.
DPMS is disabled by default.

english
30
User’s Guide - Advanced setup
F35 User’s Guide - Advanced setup
6.9 Disabling LED indicators
In certain installations it may desirable to completely disable the LED indicator in the keypad of the projector. To disable the LED indicators, go to menu entry SETTINGS > LED
INDICATORS MUTE.
If the LED indicators are enabled, the timeout period can be set in the menu under SET-
TINGS > BACKLIGHT TIMEOUT.
6.10 Setting the background color
The background color displayed when the projector is searching for a source can be set to a set of predefined colors. Go to menu entry SETTINGS > BACKGROUND to set the desired color. Default is black.
6.11 Setting OSD menu timeout
If the OSD menu is open and not used for a defined period of time, it will automatically be disabled. The default time is 30 seconds. This timeout interval can be controlled from 5 sec- onds to 60 seconds. The timeout can also be set to “never” for the OSD menu to never time out. Go to menu entry SETTINGS > MENU TIMEOUT to change this setting.
6.12 Selecting the startup logo
When the projector is starting up, a logo is displayed in the entire image. The logo can also be set to “black” if it is desirable to disable the manufacturers default logo. Go to menu entry
SETTINGS > SPLASH to change this setting.

english
31
www.projectiondesign.com
7 Optimising the picture
The projector has power features for picture optimization. This chapter describes details in using these features. All color calibration is done using projectiondesign’s proprietary Real-
Color™ solution.
7.1 Calibration data
All projectiondesign projectors are measured and calibrated with high precision equipment at the factory for the best out-of-box experience. Over the lifetime of the lamps the characteris- tics of the projector might change slightly. The same applies when replacing lamps.
7.1.1
Updating RealColor™ calibration data
For accurate results with the RealColor™ system, accurate measurement data is required.
RealColor™ calibration data can be found under the menu entry PICTURE > CALIBRATION >
REALCOLOR CALIBRATION > MEASURED VALUES
X, Y and relative luminance values for red, green, blue, white and BrilliantColor™ 1 is entered in this menu. The BrilliantColor™ should all be set to 0.000 for the VizSim (RGBRGB) color wheel. All values can also be updated using the communications protocol over RS-232 or
LAN.
IMPORTANT! Before setting these values, it is important to select the desired Brilliant-
Color™ setting. Go to menu entry PICTURE > REALCOLOR > BRILLIANTCOLOR to select the desired BrilliantColor™ look.
Measurements must be done on the built in test patterns. This is in particularly important for the BrilliantColor™ 1 test pattern since it is impossible to generate this pattern correctly using a computer source. In the user menu these patterns can be accessed through PICTURE >
CALIBRATION > REALCOLOR CALIBRATION > CALIBRATION TESTIMAGE. Use the arrow keys to cycle through the images.
NOTE! Performing a factory reset of the projector will restore the measured values to the values measured in the factory.
NOTE! When measuring data, a high quality measurement instrument is highly recom- mended for accurate results. Spectrometers (like PhotoResearch PR-655) are preferred.
TIP! For an easier calibration procedure, automated calibration can be achieved using projectiondesign’s software package ProNet. A license for the calibration software pack- age of ProNet must be purchased separately.

english
32
User’s Guide – Optimising the picture
F35 User’s Guide – Optimising the picture
7.2 Working with RealColor™
7.2.1 Setting the BrilliantColor™ correctly
The BrilliantColor™ setting is used to control how color boost is applied in the image. It can operate in four modes:
• Computer Native (Default): This give max brightness and color boost. Recommended for non-video applications, like CAD and visualization.
• Computer Balanced: Gives the same brightness as Computer Native, but has a less ag- gressive color boost profile.
• Video Native: Gives less brightness than computer, but will appear with significantly less noise in video content.
• Video Balanced: Same brightness as Video Native, but with a smoother color boost profile.
• Off: Only recommend for applications requiring a pure red, green, blue mix of colors. No secondary color or white are added to the mix.

english
33
www.projectiondesign.com
7.2.2 Gamma
The projector features a set of 6 built in gamma curves: Film 2.2, Film 2.8, Video 1, Video 2,
Computer 1, Computer 2. The different gamma curves are displayed below.
TIP! The names of the curves are descriptive for their recommended use. Use any of the computer curves for video applications will results in significant image noise.
Figure 7-1. Film 2.2 gamma
Figure 7-2. Film 2.8 gamma
Figure 7-3. Video 1 gamma

english
34
User’s Guide – Optimising the picture
F35 User’s Guide – Optimising the picture
Figure 7-4. Video 2 gamma
Figure 7-5. Computer 1 gamma
Figure 7-6. Computer 2 gamma

english
35
www.projectiondesign.com
7.2.3
RealColor™ operating modes
Before any color correction is applied to the image, the feature must be enabled. Go to menu entry PICTURE > REALCOLOR > COLOR CORRECTION to enable RealColor™.
RealColor™ can operate in 3 modes:
• Color temperature/white point correction only.
• Red, Green, Blue, White correction. In this mode optimal color coordinates for Cyan,
Magenta and Yellow will be computed automatically.
• Red, Green, Blue, Cyan, Magenta, Yellow, White. In this mode color points and intensity for each color can be manipulated separately.
To change the RealColor™ mode, please go the menu entry PICTURE > REALCOLOR >
DESIRED VALUES > DESIRED COORDS MODE.
7.2.4
Setting a white point or color temperature
After enabling RealColor™, set the color temperature in the menu entry PICTURE > REAL-
COLOR > COLOR TEMPERATURE. Values between 3200K and 9300K can be selected.
These color temperatures are tracking the “black body curve”- the black curved line in the center of CIE Chart in Figure 7-7. The default is the D65 illuminant at 6500K.
Figure 7-7. CIE Chart with the black body
The white point can also be set to a custom value defined by an x, y coordinate not linked to the black body. Go to menu entry PICTURE > REALCOLOR > X-COORDINATE and PIC-
TURE > REALCOLOR > Y-COORDINATE to change the white point.

english
36
User’s Guide – Optimising the picture
F35 User’s Guide – Optimising the picture
7.2.5 Defining the system color gamut
All colors visible to the eye are defined by CIE Chart in Figure 7-7. The boundary of the colors the projector can display is called the system color gamut. The white triangle in Figure 7-7 is an example of a system color gamut. By default the projector has the widest possible system gamut, which is limited by the color wheel selected for the system. The VizSim color wheel has the widest color gamut and the High Brightness color wheel has the smallest.
IMPORTANT! The system color gamut cannot be expanded outside color gamut defined by the color wheel.
It may be desirable to change the system color gamut of the projector to:
- Color match multiple projectors.
- Meet defined color standards, like REC 709.
- Create a special “look” to the image.
Before the system color gamut can be change the desired RealColor™ mode has to be defined. To change the RealColor™ mode, please go the menu entry PICTURE > REAL-
COLOR > DESIRED VALUES > DESIRED COORDS MODE.
RealColor™ has to be enabled for the desired system gamut to be applied. Go to menu entry
PICTURE > REALCOLOR > COLOR CORRECTION to enable RealColor™.
After RealColor™ is enabled and the desired color correction mode is selected, please go the menu entry PICTURE > REALCOLOR > DESIRED VALUES to change the color points to the your desired system color gamut.
TIP! For graphical visualization of the system color gamut and easy color management for a single or multiple projectors, the ProNet software package could be used. A license for the calibration software package of ProNet must be purchased separately.

english
37
projector
DLP® digital projector display technology single chip DMD™ (Digital
Micromirror Device™)
connectivity computer/video
2x HDMI (1.3)
concept sealed, all-glass optical design with lens shift
2x DVI-D
available resolutions
2560 x
1600
colours
30-bit colour management accuracy
± 0.002 on x, y, z axis with VizSim colour wheel control and com- munication
1x RJ45 TCP/IP network port input signal compatibility computer up to 2560 x 1600 pixels
1x RS232 9-pin DSUB (in)
horizontal scan frequency
15 - 150 kHz
1x USB-A – firmware upgrade vertical scan frequency
48 - 190 Hz
1x USB-B - reserved for future use
2x 12V (60mA) triggers (screen drop
/ aspect)
1x RC repeater, 3.5mm mini jack
2 x BNC external sync (in/out)
330 MHz digital RGB (DVI or HDMI)
optics available lenses fixed focal ultra wide angle
EN42
(503-0223-00)
supplied accessories cables
4m power cord (country dependant)/
HDMI/
DVI-dual link ultra wide angle zoom
EN45
(503-0250-00)
other backlit IR remote control, ceiling mount cable cover wide angle zoom
EN43
(503-0224-00)
product documentation standard zoom
EN41
(503-0222-00)
general dimensions (dwh)
376 x 510 x 223 mm (ex. lens)
long throw zoom
EN44
(503-0225-00)
weight about 12.6 kg (ex. lens)
environmental
RoHS, WEEE
focusing distance
0.5 - 40m (see separate lens specifications)
security
4-digit PIN code, Kensington lock optical lens shift vertical and horisonal power require- ments
100 – 240 VAC, 50/60 Hz, +/- 10%
EN42 on axis only
<1050W power consumption colour wheel options
RGBRGB – visualization & simulation
BTU/hr
<2900
RGBW – graphics display conformances
CE, CSA “C/US”, FCC Class A, CCC
RGBCW – high brightness display operating tem- perature
0 – 40ºC / 32 – 104ºF, 0 – 1500 m lamp
2 x 300W UHP™
0 – 35ºC / 32 – 95ºF, 1500 – 3000 m lamp life
2000 hrs (5000 hrs in eco relay mode)
operating and storage
20 – 90% RH
replacement lamp part no.
400-0500-00
available colours black metallic warranties
2 years, 24/7, 500 hours or 90 days on lamp
Up to 5 years total extended warranty available. Conditions apply.
www.projectiondesign.com
8 Technical specifications
8.1 Product details

english
38
User’s Guide - Technical specifications
F35 User’s Guide - Technical specifications

english
39
Please refer to our website at projectiondesign.com to download the required files or seek other information
9 Maintenance
9.1 Software upgrades
In order to upgrade your projector, please follow the method described below.
• You will need a USB stick set up with a FAT-file system to perform this upgrade
• Access the upgrade software from the following web-address; www.projectiondesign.com
• Download and save the 010.firmware.zip file to your PC desktop
• Unzip and extract the firmware file to the root of a USB memory stick
• Set the projector in standby mode
• Insert the USB stick in the projector and wait for a few seconds
• The LCD display will indicate that it has detected an upgrade file on the memory stick.
Wait a few seconds while the file is validated
• Remove the memory stick when the LCD display instructs you to do so.
PS! Important that the USB is safely removed from computer, using the eject function on your PC
• Do not remove the power cord while the upgrade is still in progress
• The projector may restart several times during the upgrade
The upgrade has finished successfully when the ordinary LCD display returns, as shown below.

english
40
User’s Guide – Maintenance
9.2 Lamp replacement
The LAMP indicators on the keypad will turn red when lamp life expires.
Change the lamp when lifetime expires. Always replace lamp with the same type and rating.
USE ORIGINAL LAMPS ONLY.
The lamp includes an electronic lamp timer that is tracking the life time of the lamp.
Allow lamp to cool down before changing. One lamp may be changed while the other lamp is operating (hot-swap).
Release the screw (LAMP 1) or (LAMP 2) depending on which lamp that needs to be re- placed.
WARNING! Be careful not to touch the protective glass when replacing the lamp house, this may cause the protective glass to overheat and break while in use.
WARNING! Be extremely careful when removing the lamp module. In the unlikely event that the bulb ruptures, small glass fragments may be generated. The lamp module is designed to contain these fragments, but use caution when removing the lamp module.
A Open the lamp lid(s).
B Turn the three locking screws a quarter turn anti-clockwise.
C Pull the lamp out.
D Replace with a new lamp in reverse order.
E Insert a new lamp. Observe the guide pins.
F Turn the tree locking screws a quarter turn clockwise.
G Close the lamp lid.
H Turn the locking screw clockwise.
A
B
H
G
F
E
D
C



601-0229-01
All brands and trade names are the property of their respective owners. Specifications subject to change without prior notice.
All values are typical and may vary. Please visit our website for latest specifications and product updates.
head office projectiondesign as
Habornveien 53
N-1630 Gamle Fredrikstad,
Norway ph +47 69 30 45 50 fx +47 69 30 45 80
sales@projectiondesign.com regional contacts
USA – Americas projectiondesign LLC
295 North Street,
Teterboro, NJ 07608,
USA
ph +1 888 588 1024 fx +1 201 288 1034
UK and Ireland – UK, Ireland
7200 The Quorum
Oxford Business Park North
Oxford, OX4 2JZ
United Kingdom ph +44 1865 487225 fx +47 69 30 45 80
uk_sales@projectiondesign.com
Germany – Germany, Austria, Swtizerland
Stuttgart ph +49 7153 958263
mo +49 (176) 2316 0345
fx +47 69 30 45 80
germany_sales@projectiondesign.com
Netherlands – Benelux region
Postbus 59 4190CB Geldermalsen, The Netherlands ph +31 (0) 345753314 fx +31 (0) 345753314
benelux_sales@projectiondesign.com
Sweden – Sweden
Flöjelbergsgatan 7A
S-43137 Mölndal
Sweden ph +46 705 253 510 fx +47 69 30 45 80
Spain – Spain, Portugal
Gorrondatxe 15, bajo A,
48640 Berango, Spain,
ph 34 676 266 301fx +47 69 30 45 80
iberica_sales@projectiondesign.com
Italy – Italy, Southern Europe
Via Plinio 43,
I-20129 Milano (MI),
Italy ph +39 02 87168210 fx +39 02 45471865
Poland – Central and Eastern Europe
Choszczno,
PL 73-200,
Poland ph +48 883 388 035 fx +47 69 30 45 80
Panama – Central and South America
Paseo Del Mar
Bayside, Suite 1301, Costa Del Este,
Panama City
Republic of Panama ph +507 69 800 555 fx +47 69 30 45 80
Hong Kong – Greater China, Taiwan, ASEAN
22/F, Hing Yip Commercial Centre,
280 Des Voeux Road Central,
Hong Kong ph +852 2858 9891 fx +852 2858 9850
South Africa – Africa, Israel
1 Peterhof Close,
Hout Bay 7806,
South Africa ph + 27 21 79 00 018 fx +47 69 30 45 80
Singapore – Greater China
Block 161 Kallang Way,
#04-05 Kolam Ayer Industrial Estate,
Singapore 349247,
Singapore ph +65 9621 7421 fx +47 69 30 45 80
India – SAARC Region
Mumbai,
India ph +91 98 20 61 06 70 fx +47 69 30 45 80
Dubai – UAE and Middle East
PO Box 17633
LOB 15 Office 212
JAFZ,
Dubai ph +9714 (4) 8872525 fx +47 69 30 45 80
locations master.indd 1 03.03.2011 13:37:29
©2010 projectiondesign AS. All rights reserved. All brands and trade names are the property of their respective owners. Specifications subject to change without prior notice. All values are typical and may vary. Please visit our website for latest specifications and product offerings.
601-0228-01
projectiondesign locations www.projectiondesign.com




Share with your friends:
  1   2


The database is protected by copyright ©userg.info 2017
send message

    Main page

bosch
camera
chevrolet
epson
fiat
Honda
iphone
mitsubishi
nissan
Panasonic
Sony
volvo
xiaomi
yamaha